Headlight Guard Husqvarna Norden 901

The Rally Dual LED headlamp assembly is really cool. It's also $654 to replace......

Protect it from impact damage with the SRC Designs Headlamp guard kit. Laser-cut 14 gauge steel powder coated satin black provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!  

All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools. 

Available in powder coated black or stainless steel (silver)

Fits Honda CRF 250L Rally & 300L Rally 2017-2025

Installation video here.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Rear Brake Master Cylinder Guard Honda 300L & Rally 

Fits: 2021 -2025 Honda 300L & Rally

Protect the vulnerable rear master cylinder from a catastrophic failure from a tip-over or impact by flying debris that could leave you without brakes!  

• Constructed of 2mm thick 304 stainless steel for maximum protection! 
• Easily installed in just a couple of minutes to provide a lifetime of protection. 
• Easy install with common hand tools.  

Available in natural stainless finish or satin black powder coat. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Protect your 300L's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate. 

• Made of 5mm thick aerospace-grade aluminum sheet with stainless hardware 
• Gussets are welded with parity to the parent material and anodized to provide strength and protection from corrosion
• Developed for on and off-road use
• Cutouts allow access to common service points without the need for removal of skid plate

Available in both Silver Aluminum and Satin Black Powder Coat options

Installation instructions

The 300L Rally skid plate/Crashbar combo is available here. 

The 300L skidplate can be installed on the Rally models by removing / trimming the bodywork plastics. 

Here's a link to a video of the process by a friend of ours. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

2025 Rally models have new wider bodywork. We have confirmed that our crash bars with integrated skid plate do fit! 

Product instructions located here

Protect your 300L Rally's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's innovative heavy-duty skid plate/crash bar combo! 

The innovative desing features an integrated aluminum skid plate and is lighter and increases structural integrity over the competitins 2 piece designs. 

In regards to a conventional full upper and lower crash bar set for the Rally, It’s SRC’s opinion that the upper front side fairing mounts aren’t strong enough for a full crash bar set. The only upper attachment point is on the bikes Rally tower frame and any impacts to the crash bar would end up damaging the tower frame structure, so they developed this kit below. Plus in most falls, the end of the handlebar and footpeg hold the bodywork away from the ground. 

To Clarify- 

This kit does not fit the 250L or 250L Rally!

300L model owners: *see detail at the bottom of this page regarding installation on the 300L. 

• Stout 1" (25mm) drawn over mandrel crash bar tube (DOM) with 1/8" (3mm ) wall thickness
• Skid plate is made of 11 gauge ( 1/8" / 3mm) thick  304 aluminum sheet with stainless hardware. 
• Developed for on and off-road use
• Cutouts allow access to common service points without the need for removal of skid plate
• Weight  16.5 lbs / 7.5kg

* We have had inquiries about fitting this kit to the 300L, and it does fit, but be aware that the crash bars are positioned a couple of inches away from the motor to clear the Rally's bodywork. Here are a few photos from a customer that installed them on his new 300L recently.   

SRC Designs Radiator Guard kit fits HONDA CRF 300L (& RALLY) 2021-2025 models

Laser-cut 2 mm thick Stainless steel and symmetrical honey-comb design provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!  

All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools. 

Available in powder coat black or natural silver

Product instructions located HERE

Installation video:  For 300L Below

Installation Video for 300L Rally Below 

2025 Rally Install shown below

•  Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
  

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC Crash Bars have cool sacrificial nylon pads that are strategically positioned to be the point of impact if you happen to drop your bike or have a tip over.  If you do happen to scratch one up, you can easily remove it and install a freshie!

These are designed to fit 1" diameter bars. All SRC bars are 1" and they should fit other brands of crash bars that are 1"/25mm diameter. 

 Please Note: These are not solid frame sliders.  Frame sliders are designed to grind away in a fall on the pavement at speed. These are more for tip-overs at low speed to protect the crash bars from scratches etc.  

Price is per replacement pad. (order 1 pad, get 1 pad)