Protect the vulnerable rear master cylinder from a catastrophic failure from a tip-over or impact by flying debris that could leave you without brakes!
Constructed of 2mm thick 304 stainless steel for maximum protection!
Easily installed in just a couple of minutes to provide a lifetime of protection.
Easy install with common hand tools.
Available in natural stainless finish or satin black powder coat.
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
Skid Plate Engine Guard HONDA CRF 300L 2021-2024
H-CRF300L-09-01-AL
Regular price
$159.00
Save $-159.00
Protect your 300L's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate.
Made of 5mm thick aerospace-grade aluminum sheet with stainless hardware
Gussets are welded with parity to the parent material and anodized to provide strength and protection from corrosion
Developed for on and off-road use
Cutouts allow access to common service points without the need for removal of skid plate
Available in both Silver Aluminum and Satin Black Powder Coat options
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
Skid Plate and Engine Guard HONDA CRF 300L Rally 2021-2024
H-CRF300RL-V3-17-01
Regular price
$448.00
Save $-448.00
Protect your 300L Rally's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's innovative heavy-duty skid plate/crash bar combo!
In regards to a conventional full upper and lower crash bar set for the Rally, It’s SRC’s opinion that the upper front side fairing mount isn’t strong enough for a full crash bar set. The only upper attachment point is on the bikes Rally tower frame and any impacts to the crash bar would end up damaging the tower frame structure, so they developed this kit below. Plus in most falls, the end of the handlebar and footpeg hold the bodywork away from the ground.
To Clarify-
The commonly used upper front shroud point is part of the headlight and windscreen tower structure and it would be damaged in a light fall/tip over as it is of light metal construction.
Does not fit the 250L /
250L Rally models *see detail at the bottom of this page regarding installation on the 300L.
Stout 1" (25mm) drawn over mandrel crash bar tube (DOM) with 1/8" (3mm ) wall thickness
Skid plate is made of 11 gauge ( 1/8" / 3mm) thick 304 aluminum sheet with stainless hardware.
Developed for on and off-road use
Cutouts allow access to common service points without the need for removal of skid plate
* We have had inquiries about fitting this kit to the 300L, and it does fit, but be aware that the crash bars are positioned a couple of inches away from the motor to clear the Rally's bodywork. Here are a few photos from a customer that installed them on his new 300L recently.
Laser-cut 2 mm thick Stainless steel and symmetrical honey-comb design provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!
All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools.
The Rally Dual LED headlamp assembly is really cool. It's also $654 to replace......
Protect it from impact damage with the SRC Designs Headlamp guard kit. Laser-cut 14 gauge steel powder coated satin black provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!
All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools.
Available in powder coated black or stainless steel (silver)
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
Acerbis Rally Pro X-Strong Handguards
2142000001
Regular price
$104.95
Sale price
$94.00
Save $10.95
The Rally Pro X-Strong is a durable injection-molded Nylon composite handguard that features an anodized aluminum bar for ultimate protection. It includes an indexed steel bar-end insert that mounts solidly and will not allow the guard to rotate in a crash. The included X-Strong mount kit allows the protection to be mounted to the handlebar with plenty of room for cables and brake lines. Optional spoilers are sold separately.
This is a universal part that fits most adventure motorcycles: Please note that some models with adjustable windscreens may need to have the windscreen in the forward-most location, such as the Royal Enfield Himalayan, to avoid contact at full lock. These are not compatible on Honda CB500X's and Honda Africa Twins.
PLEASE NOTE: Some OEM bars will require the removal of weighted bar ends and possibly other minor modifications to install handguards.
For example-
We don't advise installing on the stock handlebars as the stock bars are super soft and usually get bent on the first drop.
On the HONDA CRF 250L and 300L including Rallys, there are a few mods needed to run aftermarket bars, mainly grinding off the locating tabs on the turn signal and start button housings. And you will need to use some stainless steel tape to increase the diameter of the bar surface where these housings clamp. And we. usually sand or file off the throttle housing tube ridges so you can't feel them after installing new grips.
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
DANGO Gripper Mount for GoPro and other POV cameras
DD-GM-BK/GY-1
Regular price
$49.95
Save $-49.95
The quick-adjust camera mount with 2-axis rotation to line up the perfect angle to capture your action shot!
Dango Designs Gripper Mount Features:
Gripper jaws clamp to irregular shapes and slippery surfaces, such as your helmet, handlebars, or your vehicle.
Slim yet durable construction allows the Gripper Mount to slip effortlessly into tight situations.
Easily movable and serves as a quick-attach fixed mount, handheld stabilizer, or mini tripod.
Flexible front web conforms to your object.
Robust dual torsion spring provides strong clamping force.
2-axis rotation for flexible and quick adjustment to reposition your camera for that perfect shot.
Compatible with ¼ in 20 mounted digital action cameras (adapter version only see below) (see adapter kit below) and all GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session and Hero 6 Black.
Mount for all Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
All hardware included.
Accessory Adapter Kit sold separately for $7.99 as described below:(recommended for use on most modern MOTO helmets to position the camera far enough away from the chin guard to allow for proper angle adjustment. See Daniels video below for a clear explanation)
Increase your camera angle and mounting options with our new adapter pack for the multisport Gripper Mount from Dango Design! The Adapter Pack makes the Gripper Mount even more flexible. Fine tune your camera’s position with the 20mm and 35mm extension arms. Make your Gripper Mount compatible with digital action cameras using the ¼” – 20 adapter.
Add On Accessory Adapter Kit Features
Compatible with Dango Design Gripper Mount and other action camera mounts
All GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session and GoPro Hero 6 Black
Makes the Dango Design Gripper Mount Compatible with ¼ in 20 mounted digital action cameras
The Gripper Mount works for Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
All hardware included
Hardware Included in add on accessory adapter kit*
20 mm Universal Extension Arm with Screw
35 mm Universal Extension Arm with Screw
1/4”-20 Universal Camera Adapter
* Gripper Mount and GoPro camera not included
Here's an independent review of the Dango Gripper mount for GoPro by the popularYouTube Moto Vlogger Daniel Olszewski. He addresses the concerns we had when we first saw one of the mounts and does a really nice job of showing how versatile the Dango Gripper is. You can check out more of Daniels work at his YouTube channel here:ReturnOfDeeO
Full Rack System+Gas Can for the CRF Honda 300L & Rally
H-CRF300-04-03-AL
Regular price
$482.00
Save $-482.00
SRC Designs Full Rack System with Gas Can for the 2021 -2024 CRF HONDA 300L & Rally 300L*
This is the Adventure Rack System you want!
Innovative modular design made of high-strength lightweight aluminum alloy. Entire rack only weighs 4.2 lbs!
Top rack surface dimensions are roughly 14” long and 9’ wide at the front, tapering to 8” at the rear.
Side racks add other 12” X 6” top surface making the full rack top surface roughly 14” X 20”
Side rack dims are approximately 12” X 8”
The SRC Designs Full Rack System includes left and right pannier racks, center tail rack, mounting hardware, and instructions (easily installed in about 30 minutes with common hand tools)
The Full Rack System + Gas Can features:
High-quality stainless steel mounting hardware, mounts using the existing steel subframe rack points (no drilling required)
Pre-Drilled for MOTO STUFF Fuel can quick-release mount. (Not compatible with ROTOPAX)
Side racks and top rack feature strategically positioned strap slots for quick and secure attachment of most brands of soft luggage.
Center tail rack is nicely sized and shaped to fit the rear of the bike and provides a nice solid foundation for luggage, camping gear, etc. The aluminum rack (weighs just over a pound) mounts to the stock steel subframe points (where the stock strap bolts are located).
Racks are powder-coated satin black for a long-lasting durable finish
Gas Can is a rugged 3l (.8 gallons) spare fuel container similar in design and function to the popular ROTOPAX cans, but shaped to fit inside the left rear SRC Pannier Rack. Includes quick-release mount and hardware that easily attaches to the inside of the left SRC pannier rack, which is pre-drilled for this mount.
Shown in photos with add-on tool tube which is not included with this kit but can be purchased separately)
NOTE: We recommend using blue thread locker on the fasteners.
Here's another more detailed video we did that also shows how the gas can is easily removed.
Please Note: The CRF 300L/Rallyspecifications indicate a max subframe load of 35 lbs. We have been loading our racks with nearly 60 pounds of gear for the past 2 years and have put about 8,000 miles on our 2 Honda 250L's over all types of terrain and we have not had any issues with the racks or subframe, but the more extreme your usage, it is something to be aware of and take into consideration.
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
PLEASE NOTE: Our front line for the 2012-2024 CRF250L, Rally 250L , 300L & Rally 300L models is 2" shorter than the stock line to reduce clutter and improve the view of the instrument cluster.
MOTO STUFFpremium Steel Braided Brake lines by CORE MOTO are made to our own specifications using only the highest quality materials includingDupont PTFEliners and a tight weave aircraft-grade stainless steel casing covered inClear, Red or Stealth Blackvinyl and an industry exclusive clear translucentHD ACRYLONsheathing to prevent abrasion and provide precise alignment on the bike.
The stainless steel banjo fittings are powder coated bright Red or Blue and are adjustable for precise fitment! Each line also comes with Stainless steel Banjo Bolts and a new set of copper sealing washers.
Upgrading to a stainless line will improve brake lever feel by reducing line expansion, especially on bike with stock rubber lines that are more than 6 months old (around 20-30 hours of use) year old which will begin to flex and balloon when the brakes are applied. Also, the smaller inside diameter of our lines reduces the volume of fluid being compressed so the response is quicker.
Our lines are made using2.5mm tubingvs the 3mm tubing most common aftermarket braided lines are made of. This improves response.
The patented adjustable banjo fittings eliminate binding issues and excessive rubbing /abrasion. (easily adjusted using pliers to grip and rotate the line at the crimp joint area) Kit includes 1 line, a set of 4 new crush washers and 2 stainless steel banjo bolts.
* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged. However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
Frame Guards HONDA CRF 300L & Rally
H-CRF300-20-01-SL (D)
Regular price
$86.00
Sale price
$58.00
Save $28.00
Pair of Frame Guards HONDA CRF 300L & 300L Rally
(Discontinued item, limited to stock on hand)
Protect the frame side spars from boot scuffs and tip-over damage with the SRC Frame guards. 2mm anodized Aluminum guards. Easy 10-minute installation adds a rugged Rally look and keeps the frame looking new.
Available in clear anodized aluminum silver or satin black powder coat.
*Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged. However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
SRC Replacement Crash Bar Pads
P-PK-01-01
Regular price
$19.00
Save $-19.00
SRC Crash Bars have cool sacrificial nylon pads that are strategically positioned to be the point of impact if you happen to drop your bike or have a tip over. If you do happen to scratch one up, you can easily remove it and install a freshie!
These are designed to fit 1" diameter bars. All SRC bars are 1" and they should fit other brands of crash bars that are 1"/25mm diameter.
Please Note: These are not solid frame sliders. Frame sliders are designed to grind away in a fall on the pavement at speed. These are more for tip-overs at low speed to protect the crash bars from scratches etc.
Price is per replacement pad. (order 1 pad, get 1 pad)
Laser-cut 14 gauge steel powder coated satin black provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!
All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools.
Available in powder coat black or natural silver
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
Kriega US-30 Drypack Soft Luggage
KUSC30
Regular price
$219.00
Save $-219.00
Kriega US-30 Drypack (This is the new 420D Cordura version released in 2019)
Yeah, you can get cheaper bags, but you can't get better bags! :-) We ended up with Kriegas after years of trying other bags on the market and we have never looked back. They are one of those purchases that you later never regret. Very satisfying high-performance stuff!
Kriega US-30 Drypack
The Kriega US-30 is 30-liter capacity 100% waterproof motorcycle tailpack. This unique design solution can fit directly to the bike's subframe or mount solidly under the seat. The US-30 also comes equipped with removable shoulder and waist straps, so it can be carried courier style, on or off the bike.
Base anti-slip mesh also doubles as a pocket to store the shoulder and waist straps when the US-30 is attached to the bike. The shoulder strap connects to the large D-rings at each end of the pack and the waist strap connects to 2 fold away buckles at the corners of the mesh-pocket.
The Kriega US-30 motorcycle tailpack is designed to work perfectly with pretty much any motorcycle, via a super secure attachment to the sub-frame. The pack is easily attached/removed by 4 x quick-release buckles, and no extra bungees or rain covers are required. The Kriega US-30 tail pack utilizes the latest generation of fitting straps: US Alloy Hook Straps allow tailpack combinations of up to 70-liters to be carried with confidence and convenience. Easy on/off with no loose straps remaining. Custom aircraft grade, 6061-T6 alloy hooks attach to the four discreet web loops located on the sub-frame of the bike. Fitting method is particularly suitable for traditional one-piece motorcycle seats and bolt-on seat pads/racks, as well as standard seats. US packs can be mounted inline or across the seat. See US Alloy Hook Strap page for full fitting instructions.
Features:
100% waterproof main body
420D Cordura Lite construction
HYPALON: abrasion resistant reinforcement
DRYPACK: removable tape-seamed liner (white)
Acetal ITW Airloc buckles
YKK water-resistant zips
6061-T6 alloy fitting hooks
Side access zip pocket (water-resistant)
Rear mesh pocket
Shoulder & waist straps
1 x set US Alloy Hook Straps included
10-year guarantee
30-liter capacity
445mm H x 295mm W x 225mm D (17.5" H x 11.6" W x 8.9" D)
Kriega US-DRYPACK HOOK STRAP SET
KAMBS
Regular price
$39.00
Save $-39.00
OS-STRAPS (pair)
Kriega OS-Straps
Fit: Upgrade alloy hooks for (pre-2012) US-10 and US-20 tailpacks or replacement fitting set for US-10, US-20 & US-30 DRYPACKS.
FEATURES
Hook: Upgrade alloy hook straps for older generation US-10 and 20 packs (standard on post 2012 product). Extra secure sub-frame fitting kit allows tailpack combinations of up to 90-litres. Fitting straps have been designed to fit virtually any style of bike. Particularly suitable for traditional one-piece seats or bolt-on seat-pads/racks.
Fitting: NB - Some bikes already have web loops attached to the seat-pad/base. In this case we still recommend the fitting of the Kriega loops, as fitting to the subframe is far stronger than to the seat.
Remove bike seat and locate the best mounting areas on the rear subframe. It may be necessary to slot the internal plastic tray if no subframe metalwork is exposed. Attach the 4x 20mm web loops securely to high strength areas of the frame. The 20mm loops are adjustable in length. Final adjustments should be carried out with the seat/pad fitted. Once set, the web must be threaded back through the adjuster to lock-off the webbing. See the threading diagram on this page. To fit the US-pack, hook on the web loop, attach the top quick-release buckle and cinch down the bag on to the bike. Always use the 2 x strap keepers on the web to manage the loose ends. Please also ensure that the quick-release buckles are correctly 'clicked'
TECH-SPECS
Custom 6061-T6 alloy hooks
Multi-position: inline or across bike seat
Easy on/off bike
No loose straps left on bike
Std. strap length 600mm
4 x Acetal ITW Airloc buckles
4 x 20mm sub-frame loops
10-year guarantee
WEIGHT: 200.00 Grams
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
Full Rack System for the CRF HONDA 300L & 300L RALLY
H-CRF300-04-02-AL
Regular price
$388.00
Save $-388.00
SRC Designs Full Rack System for the 2021-2024 CRF HONDA 300L/Rally 300L The SRC Rack is designed to allow access to the toolbox under the left side panel as can be seen in the images below.
Full rack with Fuel can is also available on our site.
Top rack surface dimensions are roughly 14” long and 9’ wide at the front, tapering to 8” at the rear.
Side racks add other 12” X 6” top surface making the full rack top surface roughly 14” X 20”
Side rack dims are approximately 12” X 8”
This is the Adventure Rack System you want!
Innovative modular design made of high-strength lightweight aluminum alloy. (Entire rack only weighs 4.8 lbs! )
The SRC Designs Full Rack System includes left and right pannier racks, center tail rack, mounting hardware, and instructions (easily installed in about 30 minutes with common hand tools)
The Full Rack System features:
High-quality stainless steel mounting hardware, mounts using the existing steel subframe rack points (no drilling required)
Pre-Drilled for MOTO STUFF Fuel can quick-release mount. (Not compatible with ROTOPAX) Although a ROTOPAX can be installed on the exterior sides., just not on the interior as shown as the ROTPAX is too tall.
Side racks and top rack feature strategically positioned strap slots for quick and secure attachment of most brands of soft luggage.
The SRC Rack is designed to allow access to the tool box under the left side panel as can be seen in the images below.
Center Tail Rack is nicely sized and shaped to fit the rear of the bike and provides a nice solid foundation for luggage, camping gear, etc. The aluminum rack (weighs just over a pound, and about 3 pounds with the side racks installed) mounts to the stock steel subframe points (where the stock seat bolts are located).
Powder-coated satin black for a long-lasting durable finish that looks great on the 300L!
Please Note: The CRF 300L/Rallyspecifications indicate a max subframe load of 35 lbs. We have been loading our racks with nearly 60 pounds of gear for the past 2 years and have put about 8,000 miles on our 2 Honda's over all types of terrain and we have not had any issues with the racks or subframe, but the more extreme your usage, it is something to be aware of and take into consideration.
Another video we did that's a bit more detailed and shows how the gas can is easily removed.
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
Kriega US-20 Drypack Soft Luggage
KUSC20
Regular price
$195.00
Save $-195.00
Kriega US-20 Drypack (This is the new 420D Cordura version released in 2019)
Yeah, you can get cheaper bags, but you can't get better bags! :-) We ended up with Kriegas after years of trying other bags on the market and we have never looked back. They are one of those purchases that you later never regret. Very satisfying high-performance stuff!
The Kriega US-20 is an award-winning, high-quality piece of motorcycle luggage offering 20 liters of capacity. Like all Kriega US bags, it is a 100% waterproof drypack with an innovative design that attaches to the rear of a bike using included buckle loops and alloy hook straps. The Kriega US-20 motorcycle bag comes equipped with removable shoulder and waist straps. It can be carried courier style, on or off the bike.
Anti-slip mesh base also doubles as a pocket to store the shoulder & waist straps or other items when the US-20 is attached to the motorcycle. The shoulder strap connects to the large D-rings at each end of the pack and the waist strap connects to 2 x tuck-away buckles at the corners of the mesh-pocket.
The Kriega US-20 dry pack motorcycle tailpack is designed to work perfectly with pretty much any motorcycle, via a super secure attachment to the sub-frame. The pack is easily attached/removed by 4 x quick-release buckles, and no extra bungees or rain covers are required. The Kriega dry bag US-20 tail pack utilizes the latest generation of fitting straps. US Alloy Hook Straps allow tailpack combinations of up to 70-liters to be carried with confidence and convenience. Easy on/off with no loose straps remaining. Custom aircraft grade, 6061-T6 alloy hooks attach to the four discreet web loops located on the frame of the bike. Fitting method is particularly suitable for traditional one-piece motorcycle seats and bolt-on seat pads/racks, as well as standard seats. US packs can be mounted inline or across the seat.
OS-18 ADVENTURE PACK is specifically designed for riding in the most demanding of environments. Use as a single stand-alone pack or as a multi-pack storage system with the addition of other packs.
Yeah, you can get cheaper bags, but you can't get better bags! :-) We ended up with Kriegas after years of trying other bags on the market and we have never looked back. They are one of those purchases that you later never regret. Very satisfying high-performance stuff!
The 100% waterproof roll-top closure(removable white liner) guarantees pack contents remain protected from the elements.
Constructed from the highest quality materials including ultra-abrasion resistant Hypalon™+ 1000D Cordura® and aircraft grade alloy hooks.
A semi-rigid SureGrip rubberized base with integrated hook loops and straps enables the pack to be mounted directly to most popular racks and pannier frames. Alternatively, it can be mounted in various ways using the alloy hooks with other Kriega loop systems, making the OS-18 a very versatile pack.
The four Integrated loops on the base of each pack are designed to:
Mount directly to most rear racks
Mount directly to pannier frames
DIMENSIONS 380(h) x 250(w) x 190(d) mm 14.9(h) x 9.8(w) x 7.5(d) ins.
CAPACITY 18 Litres -1100 cu in
WEIGHT 1000g - 35oz
Kriega Subframe Loop Straps
KASLB4
Regular price
$12.50
Save $-12.50
SUBFRAME LOOP STRAPS
Provides a strong hook-on location to mount OS-ADVENTURE PACKS or US-DRYPACKS to most types of bike.
Get an extra set so you can quickly move your US Drypacsk to another bike etc.
Simply thread around the bike subframe and back through the buckle.
4 x 500mm (20") lengths of webbing with loop and buckle at one end.
NOTE: US 20 & 30 DRYPACKS include 4 x Subframe Loops in the fitting kit.
WEIGHT 50g
DANGO Gripper Mount Accessory adaptor/extension kit
DD-GM-BK/GY/AK
Regular price
$7.95
Save $-7.95
Dango Designs Gripper Mount Features Accessory Adapter Kit sold separately for $7.99 as described below:(recommended for use on most modern MOTO helmets to position the camera far enough away from the chin guard to allow for proper angle adjustment. See Daniels video below for a clear explanation)
Increase your camera angle and mounting options with our new adapter pack for the multisport Gripper Mount from Dango Design! The Adapter Pack makes the Gripper Mount even more flexible. Fine-tune your camera’s position with the 20mm and 35mm extension arms. Make your Gripper Mount compatible with digital action cameras using the ¼” – 20 adapter.
Add On Accessory Adapter Kit Features
Compatible with Dango Design Gripper Mount and other action camera mounts
All GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session and GoPro Hero 6 Black
Makes the Dango Design Gripper Mount Compatible with ¼ in 20 mounted digital action cameras
The Gripper Mount works for Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
All hardware included
Hardware Included in add on accessory adapter kit*
20 mm Universal Extension Arm with Screw
35 mm Universal Extension Arm with Screw
1/4”-20 Universal Camera Adapter
* Gripper Mount and GoPro camera not included
Here's an independent review of the Dango Gripper mount for GoPro by the popularYouTube Moto Vlogger Daniel Olszewski. He addresses the concerns we had when we first saw one of the mounts and does a really nice job of showing how versatile the Dango Gripper is. You can check out more of Daniels work at his YouTube channel here:ReturnOfDeeO
Gas / Jerry Can
O-OT-01-01
Regular price
$86.00
Sale price
$78.00
Save $8.00
MOTO STUFF Fuel/Jerry Can with mount
Please select the application for your bike below:
Rugged 3l (.8 gallons) spare fuel container similar in design and function to the popular ROTOPAX cans, but shaped to fit inside the left rear SRC Pannier Rack. Includes quick release mount and hardware that easily attaches to the SRC rack, which is pre-drilled for this mount.
Please select the application for your bike below:
Can dimensions. 10" tall X 5" thick X 8" wide
Kriega Cam Straps
KACS150
Regular price
$22.50
Save $-22.50
KRIEGA LUGGAGE CAM STRAPS
A set of 2 Heavy-duty nylon Cam straps (5ft long) idea for attaching roll-top bags, tents etc.
Moulded Acetal buckles with ultra-aggressive grip-spikes on cam for non-slip web, even with heavy loads and wet straps.
1.5M (5ft) long, high quality 1" webbing
Low weight - 1.7oz / 50g per strap
WEIGHT: 3.5oz - 100g
Kriega Overlander OS-12 ADVENTURE PACK
KOS12
Regular price
$135.00
Save $-135.00
OS-12 ADVENTURE PACK is specifically designed for riding in the most demanding of environments. Use as a single stand-alone pack or as a multi-pack storage system with the addition of other packs in the OS range.
The 100% waterproof roll-top closure(removable white liner) guarantees pack contents remain protected from the elements.
Constructed from the highest quality materials including ultra-abrasion resistant Hypalon™+ 1000D Cordura® and aircraft grade alloy hooks.
A semi-rigid SureGrip rubberized base with integrated hook loops and straps enables the pack to be mounted directly to most popular racks and pannier frames. Alternatively, it can be mounted in various ways using the alloy hooks with other Kriega loop systems, making the OS-12 a very versatile pack.
The four Integrated loops on the base of each pack are designed to:
Mount directly to most rear racks
Mount to an OS-BASE as a side pannier or tail pack
Mount as a tail pack with Kriega OS RACK LOOPS
Hook on to an OS-32 pannier (front, rear or top)
Mount directly to most front crash bars
Mount as a tank bag with Kriega TANKor SUBFRAME LOOPS
An optional OS-SHOULDER STRAP can be hooked on to convert to a shoulder bag. (sold separately)
TECH SPEC
DIMENSIONS
360(h) x 200(w) x 160(d) mm
14.2(h) x 7.9(w) x 6.3(d) ins.
CAPACITY: 12 Litres -732 cu in
WEIGHT: 850g - 30 oz
Kriega Overlander OS-6 ADVENTURE PACK
KOS6
Regular price
$109.00
Save $-109.00
OS-6 ADVENTURE PACK is specifically designed for riding in the most demanding of environments. Use as a single stand-alone pack or as a multi-pack storage system with the addition of other packs in the OS range.
The 100% waterproof roll-top closure(removable white liner) guarantees pack contents remain protected from the elements.
Constructed from the highest quality materials including ultra-abrasion resistant Hypalon™+ 1000D Cordura® and aircraft grade alloy hooks.
A semi-rigid SureGrip rubberized base with integrated hook loops and straps enables the pack to be mounted directly to most popular racks and pannier frames. Alternatively, it can be mounted in various ways using the alloy hooks with other Kriega loop systems, making the OS-6 a very versatile pack.
The four Integrated loops on the base of each pack are designed to:
Mount directly to most rear racks
Mount to an OS-BASE as a side pannier or tail pack
Mount as a tail pack with Kriega OS RACK LOOPS
Hook on to an OS-32 pannier (front, rear or top)
Mount directly to most front crash bars
Mount as a tank bag with Kriega TANKor SUBFRAME LOOPS
An optional OS-SHOULDER STRAP can be hooked on to convert to a shoulder bag. (sold separately)
TECH SPEC
DIMENSIONS
320(h) x 200(w) x 90(d) mm
12.5(h) x 7.9(w) x 3.5(d) ins.
CAPACITY: 6 Litres - 366 cu in
WEIGHT: 550g - 19.4 oz
KRIEGA US-DRYPACK HOOK STRAP (Single)
KAMBS1S
Regular price
$16.00
Save $-16.00
Kriega US Alloy Hook Strap
The Kriega US Alloy Hook Strap is an individual replacement strap for 2012+ Kriega US-10, US-20 and US-30 packs.
Features:
1 x quick-release strap with alloy buckle
Custom 6061-T6 CNC-milled aircraft grade alloy
Easy on/off
600mm
Does not include subframe loop
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.
Kriega Rally Pack
KRR25
Regular price
$87.50
Save $-87.50
FEATURES
Pack
100% waterproof bolt-on waterproof fender pack made from 1000D Cordura. 2.5L (150 cu in) capacity – ideal for safety equipment, small tools, dry gloves, etc. Innovative ‘flush’ alloy fasteners included (see fitting).
Base
Ultra-tough Rhinotek fabric on base with 4 x heavy-duty rivets. All fasteners for dirtbike fender are included (see fitting). Pack also has a removable(hook and loop) waterproof liner for cleaning or replacement.
Fitting
Remove the white liner (hook and loop, top edge) and remove the bag from the packaging. Included with the Rally pack are 4 x alloy/stainless fasteners with nylon spacer washers. The product packaging is designed to used as a drilling guide.
Line up the guide on the rear fender and drill 4 x 6mm diameter holes. Use the optional nylon washers to ensure that the threaded fastener is below the top surface of the alloy fastener (prevents damage to the internal waterproof liner/foam). Tighten anti-clockwise and always use thread lock. Allow 24 hours to dry.
TECH-SPECS
2.5-litre (150 cu in) capacity
100% waterproof
Hook and loop closure strap
4 x CNC 6061-T6 alloy fasteners
4 x Stainless steel fasteners
1000D Cordura
RHINOTEK: abrasion-resistant fabric
DRY PACK: taped-seam liner
10-year guarantee
DIMENSIONS
200(h) x 175(w) x 70(d) mm
7.9(h) x 6.9(w) x 2.7(d) ins.
WEIGHT
300 Grams
Side stand foot enlarger HONDA CRF 300L & Rally
H-CRF300-14-01-SL
Regular price
$68.00
Save $-68.00
Made specifically for 2021-2024 Honda CRF 300L & Rally
Keeps your side stand from sinking into soft ground & hot pavement!
Don't find out the hard way why these are so popular!
Don't come back to your parked bike to find it on its side after parking on hot pavement or loose soil!
Also available in a 1/2" taller version for bikes running taller suspension settings that can often cause the bike to lean over too far on the stand.
This side stand extension offers a large contact surface (50% larger than stock) to improve the motorcycle’s parking footprint on rough surfaces and soft ground.
Easily installed in just a few minutes with common hand tools.
* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.