Royal Enfield Himalayan

Protect the vulnerable rear brake fluid reservoir from a catastrophic failure from a tip-over or impact by flying debris that could leave you without brakes!  

Constructed of 2mm thick 304 stainless steel for maximum protection! 

Easily installed in just a couple of minutes to provide a lifetime of protection. 

Available in brushed stainless steel or satin black powder coat finish. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Protect the vulnerable rear master cylinder from a catastrophic failure from a tip-over or impact by flying debris that could leave you without brakes!  

Constructed of 2mm thick 304 stainless steel for maximum protection! 

Easily installed in just a couple of minutes to provide a lifetime of protection. 

Available in brushed stainless steel or satin black powder coat finish. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Made specific for 2018-2019 Royal Enfield Himalayan

• Keeps your side stand from sinking into soft ground & hot pavement! 
• Don't find out the hard way why these are so popular! 
• Don't come back to your parked bike to find it on its side after parking on hot pavement or loose soil!

This side stand extension offers a large contact surface (50% larger than stock) to improve the motorcycle’s parking footprint on rough surfaces and soft ground.  

• Easily installed in just a few minutes with common hand tools. 
• Made in high-quality Stainless Steel for long life
• Laser-cut stainless steel with Inox hardware

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

The stainless steel SRC oil cooler cage provides full wrap-around protection of the HIMALAYAN'S vulnerable oil cooler up on the left side of the engine. A rock or stick puncture here could quickly drain the lifeblood of the engine, resulting in a seized motor in just a few minutes if it went unnoticed.  

Available in natural Stainless Steel or Black Satin Powder coat finishes. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Your HIMALAYAN comes with a beautiful classic 7" round H4 halogen headlight that actually puts out a decent swath of light!  Protect it from road debris impact damage with the SRC Designs Headlamp guard kit.

Available in your choice of satin black powder coat laser cut 14 gauge steel or natural brushed stainless steel finish.   

The SRC headlight guard provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!  

All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools. The trick pin mount system allows for quick removal for cleaning with no tools! 

Easily installed in just a few minutes with a Phillips screwdriver. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Heavy-Duty Auxillary Fuel/Jerry Can Kits for HIMALAYAN 

The generous 4-gallon tank on the HIMILAYAN provides a range of about 250 miles. Add up to another 100  miles range with SRC Auxullary fuel can kits! 

The SRC auxiliary fuel can bolts-on using existing mounting points on the HIMALAYAN upper front cargo racks.  Rugged 2 mm thick powder-coated steel brackets have lower and upper support points to provide years of safe and secure service.  Unlike other mounts on the market that only mount at the top and are prone to stress cracking from repeated flexing. 

Please Note: Unlike competitors kits, this kit is fully assembled and ready to install. We also apply a heavy duty EPDM foam seating surface to prevent vibration and improve the functionality of the retention system. 

Kit includes: 

• 1 Himalayan specific bracket (Select left or right side when ordering) 
• 1- 3L (.8 gal) gas can with integrated spout and quick release mount  

Order 2 kits and install one on each side of the bike for 6 liters (1.6 gallons) of extra fuel!

MOTO STUFF Fuel cans are 10" tall, 8" wide and 5" deep.  A flexible spout is stored under the main cap. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fuel/Jerry Can Mounting Bracket for Royal Enfield Himalayan (Bracket kit only, no tanks included)

The generous 4-gallon tank on the HIMILAYAN provides a range of about 250 miles. Add up to another 100 miles range with SRC Auxullary fuel can mounts.  Pre-drilled for easy installation of our 3L fuel cans with mounts, available on our site. 

**NOTE: The base plate is large enough to accommodate the ROTOPAX 2-1/2"  mounting plate bolt pattern but you'll need to drill them yourself.  

The SRC auxiliary fuel can Brackets bolt on using existing mounting points on the HIMALAYAN upper front cargo racks.  Rugged 2 mm thick powder-coated steel brackets have lower and upper support points to provide years of safe and secure service.  Unlike other mounts on the market that only mount at the top and are prone to stress cracking from repeated flexing. 

This product includes: Himalayan specific bracket (select left or right side when ordering) 

This product does NOT include:

• Fuel/Jerry Can (Photo shown with the fuel can mounted is for reference only)
• The Gas Can retention mount (Photo with mount is shown for reference only. The retention mount is included with the Fuel/Jerry Cans and the Fuel/Jerry Cans)

**The full bracket with Fuel/Jerry Can kits are also available on our site.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC DESIGNS GPS bracket bar 2016-2019 ROYAL ENFIELD HIMALAYAN

The SRC DESIGNS GPS bracket bar gives you a solid attachment point on your Royal Enfield Himalayan windscreen mount. Gone are the days of trying to read shaky GPS screens. Made of stainless steel and anodized aluminum, this GPS bar is built to go the distance.

The GPS mount adapter provides a sturdy 22mm (7/8" inch) diameter mounting bar that is intended for mounting most GPS mounts. It can also be used for roadbook holders or any other device that uses a  common 7/8" clamp.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Protect the vulnerable header downpipe from road debris, rocks and tip over impacts with the SRC Header pipe guard.

Made of 2mm stainless steel sheet and held securely in place with low profile stainless steel band clamps.  Easily installed in just a few minutes with common hand tools and provides years of protection.

Available in both Stainless Steel and Satin Black Powder Coat options.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Buy it now - Use it forever - Lifetime Guaranteed

COMPATIBILITY
Works seamlessly with all cell phones and devices up to 3.4 inches wide and 5/8" thick. This includes all standard and Plus sized iPhones with or without a protective case. Samsung Galaxy, LG, HTC, you name this motorcycle phone mount will hold it.. Securely.
The beauty of this mount is you're able to get any phone, with any phone case, in and out of the cradle with a single hand. Loaded with dual industrial spring creating a rock steady hold on your cell phone while allowing to easily get the phone in and out of the cradle with a single hand.

INSTALLATION 
Installation is a breeze - 2 Minute Installation
The kit comes with 3 custom fittings for 7/8", 1" and 1-1/4" bars (Also, works with 1.31" over-sized road bike or mountain bike Bars.)  And fits all SRC GPS Bars
1. Simply place the appropriate spacer over the bar. Connect the clamp with the included wrench and two screws.
2. Loosen the ball and socket joint and position the phone into the desired position. Lock into place.
3. From here you will be able to easily place and remove your phone from the mount with a single hand.
Ride off into the sunset...

TACKFORM ENDURO Overview

Installation Overview below

Made of strong 3mm aluminum alloy plate for an optimal balance of strength to weight.

Available in satin black powder coat or clear anodized natural silver to prevent oxidation 

NOTE: Accessory quick attachment kit for use with Kappa, GIVI, MONOKEY Hard Cases (and shown in the images) is NOT included but is available as an add-on kit as well on our website.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

• Available Electropolished Stainless Steel silver or Satin Black Powder Coat steel  
• Stout 1" (25mm) tube with 1/8" (3mm ) wall thickness
• CNC Laser cut bracketry and mounts for a precise fit
•  Sacrificial heavy-duty Delrin guards at critical impact zones that are easily replaced if they are damaged in a tip-over

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

For some reason, Royal Enfield failed to offer any extra fused and switched accessory circuits or a standard battery tender connector on the HIMILAYAN. So we have designed and manufactured a nice harness with some cool features that anyone should be able to install in about 15 minutes with common hand tools.  The harness is made of high-quality OEM grade materials for years of trouble-free service.  It is also protected by a 15 amp fuse. 

MOTO STUFF 12 volt accessory Harness for HIMALAYAN features:

• 2 switched 12-volt leads that are long enough to reach the handlebars or instrument cluster area. 
• SAE connector for quick connection of Battery Tender
• HITACHI waterproof micro Relay

Installation overview:

Remove the seat to gain access to the battery, connect the red lead of the MOTO STUFF harness to the positive battery terminal and the black lead to the negative battery terminal. Use the included Posi-Tap connector to attach the MOTO  STUFF relay switch wire to the Himilayan harness near the battery. Route the MOTO STUFF harness under the fuel tank, up through the triple clamps and to the handlebars or to the dash area if you are using one of our 12-volt accessory USB or 12-volt sockets (cigarette lighter style). Available below.

12-Volt Socket Version: (cigarette lighter style) This is a high-quality 12-volt socket we developed to offer an OEM appearance, with a water-resistant hinged spring-loaded cover. Easily installed in just a couple of minutes, all you need is an 8mm wrench or socket to remove the rearmost windscreen adjusting bolt  (left or right side) so you can insert the bracket of your MOTO STUFF USB/12 volt socket accessory in place. Reinstall the bolt and tighten to secure the bracket in place.  And plug the end of the MOTO STUFF HIMALAYAN harness into the USB/12 volt socket connector and you are ready to go! Step by step detailed instructions are included. 

Dual USB Version: This is a high-quality dual USB charger with an OE appearance featuring a water-resistant spring-loaded hinged cover. The dual USB charger outputs 2.1 amps for fast phone charging and features a blue led indicator to let you know it's on.

Easily installed in just a couple of minutes, all you need is an 8mm wrench or socket to remove the rearmost windscreen adjusting bolt  (left or right side) so you can insert the bracket of your MOTO STUFF USB/12 volt socket accessory in place. Reinstall the bolt and tighten to secure the bracket in place.  And plug the end of the MOTO STUFF HIMALAYAN harness into the USB/12 volt socket connector and you are ready to go! Step by step detailed instructions are included. 

All Kits include 18" 2 circuit lead (18 gauge red 12V+ and Black ground) with abrasion sheath and 2 black zip ties for secure installation.

USB Adapter- For your convenience, We've sourced a rugged Dual USB charger with aluminum housing for use with the 12 Volt socket kit-  Available below.   It does not fit flush, so it keeps the cover open about 3/4 of the way open, which provides easy access to the lower port as well as providing some protection against light rain/water exposure. 

This is a 15 AMP switched circuit, which means it is turned off and on by the bikes ignition switch.

Here's a shortlist of the average current draw for popular accessories:

• Heated Grips 3-5 AMPS
• USB Phone Charger 1-2 AMPS
• Heated Gloves 3 AMPS
• Heated Jacket 8 AMPS
• Heated Pants 6 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

You have probably noticed that the stock windscreen on the Royal Enfield Himalayan is just a bit short and allows some wind buffeting to occur at cruising speeds. There are a few companies on eBay offering taller windscreens or clip-on products, but all the ones we tested had considerable quality issues. We finally found a reputable windscreen manufacturer that was willing to make a windscreen specifically for us to our specifications. It's 2” / 50mm taller than the stock windscreen and available in smoke or clear for your viewing pleasure!

Easily installed in just a couple of minutes using 5mm allen wrench.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Kriega US-30 Drypack (This is the new 420D Cordura version released in 2019) 

Yeah, you can get cheaper bags, but you can't get better bags! :-)  We ended up with Kriegas after years of trying other bags on the market and we have never looked back. They are one of those purchases that you later never regret. Very satisfying high-performance stuff! 

Kriega US-30 Drypack

The Kriega US-30 is 30-liter capacity 100% waterproof motorcycle tailpack. This unique design solution can fit directly to the bike's subframe or mount solidly under the seat. The US-30 also comes equipped with removable shoulder and waist straps, so it can be carried courier style, on or off the bike.

Base anti-slip mesh also doubles as a pocket to store the shoulder and waist straps when the US-30 is attached to the bike. The shoulder strap connects to the large D-rings at each end of the pack and the waist strap connects to 2 fold away buckles at the corners of the mesh-pocket.

The Kriega US-30 motorcycle tailpack is designed to work perfectly with pretty much any motorcycle, via a super secure attachment to the sub-frame. The pack is easily attached/removed by 4 x quick-release buckles, and no extra bungees or rain covers are required. The Kriega US-30 tail pack utilizes the latest generation of fitting straps: US Alloy Hook Straps allow tailpack combinations of up to 70-liters to be carried with confidence and convenience. Easy on/off with no loose straps remaining. Custom aircraft grade, 6061-T6 alloy hooks attach to the four discreet web loops located on the sub-frame of the bike. Fitting method is particularly suitable for traditional one-piece motorcycle seats and bolt-on seat pads/racks, as well as standard seats. US packs can be mounted inline or across the seat. See US Alloy Hook Strap page for full fitting instructions.

Features:

• 100% waterproof main body
• 420D Cordura Lite construction
• HYPALON: abrasion resistant reinforcement
• DRYPACK: removable tape-seamed liner (white)
• Acetal ITW Airloc buckles
• YKK water-resistant zips
• 6061-T6 alloy fitting hooks
• Side access zip pocket  (water-resistant)
• Rear mesh pocket
• Shoulder & waist straps
• 1 x set US Alloy Hook Straps included
• 10-year guarantee
• 30-liter capacity 
• 445mm H x 295mm W x 225mm D (17.5" H x 11.6" W x 8.9" D)

SRC Tool Tube and Mount (shown with the full SRC Designs Rack system)

Kit includes a watertight HDP plastic (High-Density Polypropylene) tool tube with rubber o-ring seal and custom mounting brackets that align with the pre-drilled points on the left or right SRC Side Pannier Rack.

Tool tube Dimensions

• Length: 12" / 300mm
• Inside Diameter: 4-1/2"  / 108mm
• Outer diameter: 5" / 124mm

The quick-adjust camera mount with 2-axis rotation to line up the perfect angle to capture your action shot!

Dango Designs Gripper Mount Features:

• Gripper jaws clamp to irregular shapes and slippery surfaces, such as your helmet, handlebars, or your vehicle.
• Slim yet durable construction allows the Gripper Mount to slip effortlessly into tight situations.
• Easily movable and serves as a quick-attach fixed mount, handheld stabilizer, or mini tripod.
• Flexible front web conforms to your object.
• Robust dual torsion spring provides strong clamping force.
•  2-axis rotation for flexible and quick adjustment to reposition your camera for that perfect shot.
• Compatible with ¼ in 20 mounted digital action cameras (adapter version only see below) (see adapter kit below) and all GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session and Hero 6 Black.
• Mount for all Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
• All hardware included.

Accessory Adapter Kit sold separately for $7.99 as described below: (recommended for use on most modern MOTO helmets to position the camera far enough away from the chin guard to allow for proper angle adjustment. See Daniels video below for a clear explanation) 

Increase your camera angle and mounting options with our new adapter pack for the multisport Gripper Mount from Dango Design! The Adapter Pack makes the Gripper Mount even more flexible. Fine tune your camera’s position with the 20mm and 35mm extension arms.  Make your Gripper Mount compatible with digital action cameras using the ¼” – 20 adapter.

Add On Accessory Adapter Kit Features

• Compatible with Dango Design Gripper Mount and other action camera mounts
  • All GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session and GoPro Hero 6 Black
• Makes the Dango Design Gripper Mount Compatible with ¼ in 20 mounted digital action cameras
• The Gripper Mount works for Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
• All hardware included

Hardware Included in add on accessory adapter kit*

• 20 mm Universal Extension Arm with Screw
• 35 mm Universal Extension Arm with Screw
• 1/4”-20 Universal Camera Adapter
• * Gripper Mount and GoPro camera not included

Here's an independent review of the Dango Gripper mount for GoPro by the popular YouTube Moto Vlogger Daniel Olszewski. He addresses the concerns we had when we first saw one of the mounts and does a really nice job of showing how versatile the Dango Gripper is.  You can check out more of Daniels work at his YouTube channel here: ReturnOfDeeO

Dango Designs Gripper Mount Features Accessory Adapter Kit sold separately for $7.99 as described below: (recommended for use on most modern MOTO helmets to position the camera far enough away from the chin guard to allow for proper angle adjustment. See Daniels video below for a clear explanation) 

Increase your camera angle and mounting options with our new adapter pack for the multisport Gripper Mount from Dango Design! The Adapter Pack makes the Gripper Mount even more flexible. Fine-tune your camera’s position with the 20mm and 35mm extension arms.  Make your Gripper Mount compatible with digital action cameras using the ¼” – 20 adapter.

Add On Accessory Adapter Kit Features

• Compatible with Dango Design Gripper Mount and other action camera mounts
  • All GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session and GoPro Hero 6 Black
• Makes the Dango Design Gripper Mount Compatible with ¼ in 20 mounted digital action cameras
• The Gripper Mount works for Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
• All hardware included

Hardware Included in add on accessory adapter kit*

• 20 mm Universal Extension Arm with Screw
• 35 mm Universal Extension Arm with Screw
• 1/4”-20 Universal Camera Adapter
• * Gripper Mount and GoPro camera not included

Here's an independent review of the Dango Gripper mount for GoPro by the popular YouTube Moto Vlogger Daniel Olszewski. He addresses the concerns we had when we first saw one of the mounts and does a really nice job of showing how versatile the Dango Gripper is.  You can check out more of Daniels work at his YouTube channel here: ReturnOfDeeO

Version 1 SRC DESIGNS GPS bracket bar 2016-2019 ROYAL ENFIELD HIMALAYAN

Made of stainless steel and anodized aluminum, this handlebar mounting adapter is built to go the distance. Available in satin black powder coat - There are only a few left of this early version.

The GPS mount adapter provides a sturdy 22mm (7/8" inch) diameter mounting bar that is intended for mounting most GPS mounts. It can also be used for roadbook holders or any other device that uses a common 7/8" clamp.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

The NEW OS-BASE is the latest addition to the range. An innovative modular pannier system that fits virtually any trail, enduro or dual sport bike without the need for metal pannier frames.

The OS-BASE is an over the seat harness' which allows OS-6, OS-12 or OS-18 ADVENTURE PACKS to be mounted as panniers.

The modular design enables you to modify your luggage set-up to suit your ride - from a day’s single track to longer adventure trips.

By adding an additional OS-ADVENTURE PACK as a top bag, you have a possible 100% waterproof, highly durable carrying capacity of up to 54 liters.

The flexible design of the OS-BASE also enables you to mount earlier model Overlander 15 packs as panniers, US-DRYPACKS as top bags and includes ‘Loop Mounts' to attach a tent or sleeping mat.

After the initial set-up, it’s quick and easy to put on and take off and the heavy-duty hypalon construction with a semi-rigid polypropylene core is very stable and lightweight.

The unique OS-RACK LOOP mounting system,* provides a very tough and reliable solution to the demands of off-road luggage carrying. 

*Includes 2 x OS-RACK LOOPS which require 2 x 6mm holes drilled in the rear fender for fitting.

FEATURES

• Carrying capacity from 12 to 54 Litres with center pack mounting option.
• Heavy-duty Hypalon™ construction.
• Quick & easy to put on/take off.
• Reinforced stitching on all stress points.
• Aircraft grade alloy hooks.
• Non-slip cam buckles.
• 2 x OS-RACK LOOPS included.
• 10 YEAR GUARANTEE

FITTING OPTIONS

Once the OS-RACK LOOPS are mounted on the rear fender and the OS PACKS of your choice are mounted to the BASE, fitting is quick and easy.

1. Hook-on the two top straps to the OS Rack Loops but leave loose.

2. Loop the two lower straps around the bike frame at the lowest possible position and hook them back to the loops on the strap making them as tight as possible.

3. Stand at the rear of the bike and pull the top straps as tight as possible, taking up the slack until the packs fit tightly to the bike.

4. Hook-on an additional top pack to the Loop Mounts on the OS-BASE and the OS-Rack Loops.

IMPORTANT If the OS-BASE is in contact with the exhaust silencer you must fit a heat shield.

DIMENSIONS
510(L) x 190(w) mm
20(L) x 7.5(w) ins.

WEIGHT
700g - 24.7oz

KRIEGA LUGGAGE CAM STRAPS

A set of 2 Heavy-duty nylon Cam straps (5ft long) idea for attaching roll-top bags, tents etc.

Moulded Acetal buckles with ultra-aggressive grip-spikes on cam for non-slip web, even with heavy loads and wet straps.

1.5M  (5ft) long, high quality 1" webbing

Low weight - 1.7oz / 50g per strap

WEIGHT
3.5oz - 100g

Kriega US-20 Drypack (This is the new 420D Cordura version released in 2019)

Yeah, you can get cheaper bags, but you can't get better bags! :-)  We ended up with Kriegas after years of trying other bags on the market and we have never looked back. They are one of those purchases that you later never regret. Very satisfying high-performance stuff! 

The Kriega US-20 is an award-winning, high-quality piece of motorcycle luggage offering 20 liters of capacity. Like all Kriega US bags, it is a 100% waterproof drypack with an innovative design that attaches to the rear of a bike using included buckle loops and alloy hook straps. The Kriega US-20 motorcycle bag comes equipped with removable shoulder and waist straps. It can be carried courier style, on or off the bike. 

Anti-slip mesh base also doubles as a pocket to store the shoulder & waist straps or other items when the US-20 is attached to the motorcycle. The shoulder strap connects to the large D-rings at each end of the pack and the waist strap connects to 2 x tuck-away buckles at the corners of the mesh-pocket.

The Kriega US-20 dry pack motorcycle tailpack is designed to work perfectly with pretty much any motorcycle, via a super secure attachment to the sub-frame. The pack is easily attached/removed by 4 x quick-release buckles, and no extra bungees or rain covers are required. The Kriega dry bag US-20 tail pack utilizes the latest generation of fitting straps. US Alloy Hook Straps allow tailpack combinations of up to 70-liters to be carried with confidence and convenience. Easy on/off with no loose straps remaining. Custom aircraft grade, 6061-T6 alloy hooks attach to the four discreet web loops located on the frame of the bike. Fitting method is particularly suitable for traditional one-piece motorcycle seats and bolt-on seat pads/racks, as well as standard seats. US packs can be mounted inline or across the seat.

Kriega US-20 dry pack features:

• 100% waterproof main body
• 420D Cordura Lite construction
• HYPALON: abrasion resistant reinforcement
• DRYPACK: removable tape-seamed liner (white)
• 420D nylon ripstop - lightweight yet extremely strong
• 6061-T6 alloy fitting hooks
• Acetal ITW Airloc quick-release buckles
• YKK water-resistant zip on side pocket
• Side access zip pocket (water-resistant)
• Rear mesh pocket
• Shoulder & waist straps
• US Alloy Hook Straps included
• 10-year guarantee
• 20-liter capacity     
• 15.7" H x 10.2" W x 7.5" D

OS-SHOULDER STRAP (sold each)

Convert your OS-ADVENTURE PACK or OS-32 /22 /18 SOFT PANNIER into a shoulder bag for easy carrying off the bike.

• Fits OS-6, OS-12, OS-18 , OS022 & OS-32 PACKS
• Length adjustable
• Ultra-tough HYPALON™ shoulder pad
• Aircraft grade alloy buckles

WEIGHT
100g