PLEASE NOTE!

The Dual USB-A socket shown in the installed option images below is no longer available; it has been replaced with this new and improved illuminated  USB A&C version. 

PLEASE DOUBLE CHECK YOUR SELECTION BEFORE CHECKING OUT!

Fits 2017 to 2025 Honda CRF 250L Rally/300L Rally models

HONDA was nice enough to include a handy 10 AMP* switched accessory lead that is clipped inside the left front fairing on the CRF 250L Rally & 300L Rally models, however, they have yet to release an accessory lead to plug into it! So we picked up the ball and sourced the correct original HONDA waterproof connectors and built them. All leads are 18" long and allow for safe routing from the left upper fairing, following the factory harness routing to the Rally tower and the mount easily installs using a rubber well nut. 

Two options are available to choose from: 12-volt & Dual USB

Please note, the 250 & 300 installs are the same. 

Please select between these two versions of the Electrical Accessory Lead:

• Dual USB option
• 12-Volt Socket option

Dual USB Version: This is a high-quality dual USB charger with an OE appearance featuring a water-resistant spring-loaded hinged cover. The dual USB charger outputs 2.1 amps for fast phone charging and features a blue led indicator to let you know it's on. Easily installed in just a couple of minutes, all you need is an 8mm wrench or socket to tighten the well nut to secure the bracket to the Rally Tower tube. (remove the rubber plug from the left end of the upper tower bar and insert well nut and snug it up until the bracket is secure!) And plug the other end into the auxiliary power connector inside the left fairing of the Rally. 

12 Volt Socket Version: (cigarette lighter style) This is a high-quality 12-volt socket we developed to offer an OEM appearance, with a water-resistant hinged spring-loaded cover. Easily installed in just a couple of minutes, all you need is an 8mm wrench or socket to tighten the well nut to secure the bracket to the Rally Tower tube. (remove the rubber plug from the left end of the upper tower bar and insert well nut and snug it up until the bracket is secure!) And plug the other end into the auxiliary power connector inside the left fairing of the Rally. (2017-2019 CRF 250L kit mounts on the front side of the top right fork triple clamp)

Also available on our site: USB Adapter- For your convenience, We've sourced a rugged Dual USB charger with aluminum housing for use with the 12 Volt socket kit-  in the electrical Accessory section of our website.    

* This is a 10 AMP Switched circuit (fuse #5 on the Rally), which means it is turned off and on by the bikes ignition switch.

Here's a shortlist of the average current draw for popular accessories:

• Heated Grips 3-5 AMPS
• USB Phone Charger 1-2 AMPS
• Heated Gloves 3 AMPS
• Heated Jacket 8 AMPS
• Heated Pants 6 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

Quick Rally install overview for those of you that may not be familiar with well nuts. 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality. 

PLEASE NOTE! 

Late in 2024 DOUBLETAKE began to manufacture their own arms as RAM copied their rugged mirror idea and became a competitor. So DOUBLETAKE took the opportunity to further improve their product. That is what we have in stock. There are a few images shown with the old RAM parts, but the first image is what you will receive. 

Our kit includes  DoubleTakes full adapter kit to allow fitment to all adventure bikes. 

• This kit fits almost any motorcycle make and model - Each pair comes with a Universal Adapter Kit which includes two 10 x 1.25mm Extensions, two 10 x 1.5mm BMW adapters, and one Reverse-Thread Adapter. 

• Here is a quick list:
• HONDA: 250L, Rally, CB500X, NC750, Africa Twins
• KAWASAK: 300X Versys, Versys 650, Versys 1000
• KTM: All adventure models
• SUZUKI: V-Strom 650, V-Strom 1000
• TRIUMPH: Tigers
• Royal Enfield: Himalayan
  
• DUCATI: Multistrada
• BETA: 500RR-S
• BMW: 310 GS, 310 R, 800 GS, 1200 GS, 1200 GS
• YAMAHA: FJ-09, Tenere 700
• And many more!

Over the years we have tried many popular Adventure bike mirror options and always come back to the simple and durable DoubleTake ADV sets as they simply work and provide an excellent field of view with minimal vibration distortion.  We feel this is the most important feature, functionality over form. There are a bunch of small/minimalist options to choose from on the web if you're into that, but safety and visibility are most important to us and that's why we run the DOUBLETAKE ADVENTURE mirrors on all of our bikes. 

Kit includes:  2 mirrors, 2 - 6" arms, 2 - 1" ball mounts, and thread adapters for your bike if needed, a small tube of Loctite thread locker (SRC exclusive!) Apply thread locker to adapter and ball mount threads to prevent your mirrors from vibrating loose.  Everything you need to install them in just a few minutes on most bikes!  

Install Tip: We recommend using one of the extension arms tightly clamped onto the ball mount to tighten the ball mount (and adapters if needed) into the mirror mounts of your bike.  

PS- If you are price shopping, please note that we include the correct adapters and spacers for the specific models below as well as Loctite thread locker to keep them from vibrating loose! 

Below is the DoubleTake Mirror inventors story of how the DoubleTakes came to be-

This mirror is the product of much frustration- I spent years breaking other designs and wondering what was going on behind me on the road. Eventually, when I dropped my bike and found myself buying two(!) new master cylinders as a result, I decided it was time to make a really good mirror, one that would function well as a mirror, and also protect the bike (and me) from damage. I had three goals for my design: That it work as well as an OEM mirror for seeing what was going on behind. That it would be indestructible. It would have to give way in a crash to avoid damage not only to the mirror, but also to the bike. That it could fold completely out of the way, so that when I am offroad, I don't have to think about it. Many experiments later, the mirrors for sale here is the result. Both models hit all three marks right on the nose. We use SAE spec glass to give maximum visibility (it can be important to distinguish Crown Victoria headlights from other vehicles!), it is made right here in Colorado Springs from a super tough nylon that we are so certain will survive we offer a lifetime warranty (on the housing, not the glass, but you can buy the glass separately), and sure enough, it folds right down when you want it gone. If you're deciding between the Adventure model, and the Enduro, our advice is simple. If you plan to fold the mirror down a large percentage of the time, the Enduro is right for you. The long size means the head of the mirror tucks away right behind the headlight. If the mirror will more or less remain extended, get the Adventure- the more compact design is more stable at highway speeds. Either way, you can't go wrong.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

# double take

Inspired by the CRF 250l Rally's bigger brother, the mighty Africa Twin.......

4" X 1.5", the perfect size for placement on the front fender, fairing, helmet, toolbox, just about anywhere!

SOLD AS A PAIR

For some reason, the CRF 250L and 250L Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginners bike.

Fits 2013-2020 250L & Rally

So we have some options to get your feet firmly on the ground. We are pleased to offer these custom-shaped lowering seats that lower the seat height by 2". These are brand new original HONDA seats that have been hand shaped and re-formed to reduce the seat height by 2" There is still 1-1/2" of foam cushion in the main seating area, so normal ADV riding won't be an issue, but if you are a hard-charging off-roader frequently getting airborne, it might be a bit firm on some landings! :-) 

These were developed after my wife was about to give up on her Rally as it was too tall for her. She is relatively new to offroad riding and really felt unsafe and uncomfortable on the Rally, especially when riding on sidehills and slippery surfaces where she was not able to touch the ground when needed. We had already installed a lowering link and that helped, but she wanted it lower to feel comfortable. So we gave one of these a try and she now loves her Rally!  Easily installed in just a couple of minutes with common hand tools. 

Now available in your choice of RED or BLACK- Please make a selection

We occasionally get further inquiries regarding lowering options and this is our general reply: 

The cons of running a link are due to the geometry change in the suspension. In a nutshell, the bike becomes "choppered out" slightly. So the bike likes to go straight (improves straight-line stability), but when cornering on loose surfaces such as gravel roads or lose dirt, the bikes front end will have a bit more of a tendency to plow or push through corners. This is not noticeable on pavement and a beginner off road rider probably won't push the limits of traction enough to have it be an issue, but if you are an experienced off-road rider, you will most likely notice it.  

* These are brand new original HONDA seats that have been hand shaped and re-formed to reduce the seat height by 2" 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality. 

The Dual USB-A socket shown in the installed option images below is no longer available; it has been replaced with this new and improved illuminated  USB A&C version. 

PLEASE DOUBLE CHECK YOUR SELECTION BEFORE CHECKING OUT!

HONDA was nice enough to include a handy 10 AMP* switched accessory lead connector that is hidden inside a small black vinyl protective boot located behind the headlamp on the right side on 2017-2025 HONDA CRF 250L/300L models.  However, HONDA has yet to release an accessory lead to plug into it! So we picked up the ball and sourced the correct original HONDA waterproof connectors and built it.

DUAL USB Version: This is a high-quality dual USB charger with an OE appearance featuring a water-resistant spring-loaded hinged cover. The dual USB charger outputs 2.1 amps for fast phone charging and features a blue led indicator to let you know it's on. Easily installed in just a couple of minutes, all you need is a 10 mm wrench or socket to secure the mount bracket to the upper right triple clamp bolt.  And plug the other end into the auxiliary power connector mentioned above. Step by step instructions with photos are included. 

12 Volt Socket Version: (cigarette lighter style) This is a high-quality 12-volt socket we developed to offer an OEM appearance, with water-resistant hinged spring-loaded cover. Easily installed in just a couple of minutes, all you need is a 10 mm wrench or socket to secure the mount bracket to the upper right triple clamp bolt.  And plug the other end into the auxiliary power connector mentioned above. Step by step instructions with photos are included. We offer a nice rugged aluminum housing USB adapter here in the electrical section if needed. 

* This is a 10 AMP Switched circuit (fuse #5 on the Rally), which means it is turned off and on by the bikes ignition switch.

Here's a short list of the average current draw for popular accessories:

Heated Grips 3-5 AMPS

USB Phone Charger 1-2 AMPS

Heated Gloves 3 AMPS

Heated Jacket 8 AMPS

Heated Pants 6 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

Here's the connector as viewed from the right side of the bike, just behind the headlight looking upwards from the side reflector area. 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Rear Brake Master Cylinder Guard HONDA CRF 300L & Rally 

Fits: 2021 -2025 Honda CRF 300L & Rally

Protect the vulnerable rear master cylinder from a catastrophic failure from a tip-over or impact by flying debris that could leave you without brakes!  

• Constructed of 2mm thick 304 stainless steel for maximum protection! 
• Easily installed in just a couple of minutes to provide a lifetime of protection. 
• Easy install with common hand tools.  

Available in natural stainless finish or satin black powder coat. 

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE!

Fits 2016 to 2023 Royal Enfield Himalayan and SCRAM 411  models

The stainless steel SRC oil cooler cage provides full wrap-around protection of the HIMALAYAN'S vulnerable oil cooler up on the left side of the engine. A rock or stick puncture here could quickly drain the lifeblood of the engine, resulting in a seized motor in just a few minutes if it went unnoticed.  

Available in natural Stainless Steel or Black Satin Powder coat finishes. 

Product instructions located here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

HONDA was nice enough to include a handy 10 AMP* switched accessory lead that is clipped inside the left front fairing on the 2017-2020 CRF 250L Rally models. The 2017-20225 CRF 250L/300L and Rally's accessory connector is located behind the headlamp on the right side.  It is located inside a small black vinyl protective boot.  However, HONDA has yet to release an accessory lead to plug into it! So we picked up the ball and sourced the correct original HONDA waterproof connectors and built it. Leads are 18" long and allow for safe routing, following the factory harness routing to the instrument cluster area or handlebars to connect to your accessory.  

Our plug-and-play accessory lead is easy to install,  just unclip the stock connector cap, connect this lead and attach to your accessory with the included posi lock quick connectors! Posi Lock instructions are included in each kit.  

Kit includes 18" 2 circuit lead (18 gauge red 12V+ and Black ground) terminated with Posi Lock connectors with abrasion sheath and 2 black zip ties for secure installation.  Posi-Lock® Connectors have been put to the test worldwide since 1997. Superior in-line splices with just hand tightening! These electrical connectors require no crimping or soldering.  An electrical connector that meets the needs of today's OEM's, and is so good, it's reusable. Truly a connector for the 21st century.  

Easily installed in about 10 minutes with common hand tools. No modifications or cutting of any wires required. Detailed instructions with photos are included. 

Details on the Rally connector location below. 

Details on the 2017-2020 HONDA CRF 250L accessory connector location below.  (it's in a vinyl protective boot behind and below the right side of the headlight. 

The view below is from the right side of the bike looking upwards from the ara near the right side reflector.  

 This is a 10 AMP Switched circuit, which means it is turned off and on by the bikes ignition switch.

Here's a shortlist of the average current draw for popular accessories:

• Heated Grips 3-5 AMPS
• USB Phone Charger 1-2 AMPS
• Heated Gloves 3 AMPS
• Heated Jacket 8 AMPS

Heated Pants 6 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

 * Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CRASH BAR FOR BMW G 310 GS / 2017-2025

• Available Electropolished 304 Stainless Steel silver or Satin Black Powder Coat steel  
• Stout 1" (25mm) tube with 1/8" (3mm ) wall thickness
• CNC Laser cut bracketry and mounts for a precise fit

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness. Crash bars go on first, to allow easy skid plate removal for service. 

Link to installation PDF guide here

*Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Protect your 300L's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate. 

• Made of 5mm thick aerospace-grade aluminum sheet with stainless hardware 
• Gussets are welded with parity to the parent material and anodized to provide strength and protection from corrosion
• Developed for on and off-road use
• Cutouts allow access to common service points without the need for removal of skid plate

Available in both Silver Aluminum and Satin Black Powder Coat options

Installation instructions

The 300L Rally skid plate/Crashbar combo is available here. 

The 300L skidplate can be installed on the Rally models by removing / trimming the bodywork plastics. 

Here's a link to a video of the process by a friend of ours. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

2025 Rally models have new wider bodywork. We have not test fit the 2025 yet. We will update the application as soon as we have confirmed fitment.

THIS ONLY FITS THE RALLY!

Go to the non rally listing if you have the standard L or LS model. 

Fits 2021-2025 300L RALLY 

About 2" lower than stock seat

For some reason, the CRF 300L and Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginner bike.

So we have some options to get your feet firmly on the ground. We are pleased to offer these custom-shaped lowering seats that lower the seat height by about 2". These are brand new original HONDA seats that have been hand-shaped and re-formed to reduce the seat height by about 2" There is still 1-1/2" of foam cushion in the main seating area, so normal ADV riding won't be an issue, but if you are a hard-charging off-roader frequently getting airborne, it might be a bit firm on some landings! :-) 

These were developed after my wife was about to give up on her Rally as it was too tall for her. She is relatively new to offroad riding and really felt unsafe and uncomfortable on the Rally, especially when riding on sidehills and slippery surfaces where she was not able to touch the ground when needed. We had already installed a lowering link and that helped, but she wanted it lower to feel comfortable. So we gave one of these a try and she now loves her Rally!  Easily installed in just a couple of minutes with common hand tools. 

We occasionally get further inquiries regarding lowering options and this is our general reply: 

The cons of running a link are due to the geometry change in the suspension. In a nutshell, the bike becomes "choppered out" slightly. So the bike likes to go straight (improves straight-line stability), but when cornering on loose surfaces such as gravel roads or lose dirt, the bikes front end will have a bit more of a tendency to plow or push through corners. This is not noticeable on pavement and a beginner off road rider probably won't push the limits of traction enough to have it be an issue, but if you are an experienced off-road rider, you will most likely notice it.  

* These are brand new original HONDA seats that have been hand-shaped and re-formed to reduce the seat height by 2" 

 * Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.

However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality. 

SRC Designs Radiator Guard kit fits HONDA CRF 300L (& RALLY) 2021-2025 models

Laser-cut 2 mm thick Stainless steel and symmetrical honey-comb design provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!  

All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools. 

Available in powder coat black or natural silver

Product instructions located HERE

Installation video:  For 300L Below

Installation Video for 300L Rally Below 

2025 Rally Install shown below

•  Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
  

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SAVE BIG BUCKS on the best kits while supplies last!  

Crash Bars / Engine Guards 2017-2023 Royal Enfield Himalayan and SCRAM 411

• Available electropolished 304 stainless steel silver or satin black powder coat steel  
• Stout 1" (25mm) tube with 1/8" (3mm ) wall thickness
• CNC Laser cut bracketry and mounts for a precise fit
• Sacrificial heavy-duty delrin guards at critical impact zones that are easily replaced if they are damaged in a tip-over
• Design of guards allows for easy access to the oil filter

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

Product instructions located here

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.

However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

Your HIMALAYAN comes with a beautiful classic 7" round H4 halogen headlight that actually puts out a decent swath of light!  Protect it from road debris impact damage with the SRC Designs Headlamp guard kit.

Available in your choice of satin black powder coat laser cut 14 gauge steel or natural brushed stainless steel finish.   

The SRC headlight guard provides a proper defense against rocks, limbs, and other debris you might encounter on your adventures!  

All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools. The trick pin mount system allows for quick removal for cleaning with no tools! 

Easily installed in just a few minutes with a Phillips screwdriver. 

PLEASE NOTE: If you are running the windscreen in the upright position, you can install the headlight guard in that position, but it will be tilted forward a bit at the top. To keep it square to the headlight, you will have to make a slight modification to the windscreen to expose the lower mounting hole.  (use a round file to remove enough material to allow the rearmost headlight guard mounting bolts to be installed.)

Product instructions located here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits: 2012-2025 HONDA CB500X & NX500 

Kit includes a pair of wide peg adapters

If you've never run a wider high-quality footpeg, you will be pleasantly surprised by the improvement this inexpensive and easy to install upgrade will make! Upgrading to a wider platform footpeg makes a dramatic improvement in comfort as well as greatly improving grip in wet muddy conditions. Our peg adaptors are a great value and easy to install.

It only takes about 10 minutes to install with common hand tools. The additional width and aggressive tooth profile offer about more contact surface to reduce foot arch strain and improve grip. The wide platform and increased contact points will improve rider confidence in sketchy situations!

• Made of Stainless Steel
• Developed for off-road use
• 55mm wide and 90mm long

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

HONDA was nice enough to include a handy 10 AMP* switched accessory lead connector that is clipped to a metal bracket just behind the bottom of the left radiator (see photo in product listing), however, they have yet to release an accessory lead to plug into it! So we picked up the ball and sourced the correct original HONDA waterproof connectors and built this 12-volt socket version. Leads are 24" long and allow for safe routing from the lower-left radiator area following the factory harness routing to the left upper triple clamp bolt for a quick and secure mount. 

The Dual USB-A socket shown in the installed option images below is no longer available; it has been replaced with this new and improved illuminated  USB-A&C version. 

DUAL USB Version: This is a high-quality dual USB charger with an OE appearance featuring a water-resistant spring-loaded hinged cover. The dual USB charger outputs 2.1 amps per port for fast phone charging and features a blue led indicator to let you know it's on. Easily installed in just a couple of minutes, all you need is a 10mm wrench or socket to install the bracket to the upper triple clamp.  And plug the other end into the auxiliary power connector behind the lower left radiator area following the factory harness routing. 

12 Volt Socket Version: (cigarette lighter style) This is a high-quality 12-volt socket we developed to offer an OEM appearance, with a water-resistant hinged spring-loaded cover. Easily installed in just a couple of minutes, all you need is a 10mm wrench or socket to install the bracket to the upper triple clamp.  And plug the other end into the auxiliary power connector behind the lower left radiator area following the factory harness routing. 

All Kits include 18" 2 circuit lead (18 gauge Red 12V+ and Black ground) with abrasion sheath and 2 black zip ties for secure installation.

This is a 10 AMP Switched circuit, which means it is turned off and on by the bikes ignition switch.

Here's a shortlist of the average current draw for popular accessories:

• Heated Grips 3-5 AMPS
• USB Phone Charger 1-2 AMPS
• Heated Gloves 3 AMPS
• Heated Jacket 8 AMPS
• Heated Pants 6 AMPS

WARNING: Most High output horns will draw too much amperage for this circuit. If you are planning to use a 12-volt compact air compressor, be sure to check it to make sure it does not draw more than 10 amps! Usually better to get a compressor that connects to your battery tender SAE connector and ensure it's got the proper capacity.

*Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC Designs Aluminum Center Rear Cargo Rack - CRF HONDA 300L & 300L Rally 2021-2025

Top Rack Dimensions: 14" long, 10" wide at the front and tapering towards the rear to 9" wide. 

Nicely sized and shaped to fit the rear of the 2021 300L & Rally and provides a nice solid foundation for luggage, camping gear, etc. The aluminum rack (weighs just over a pound) mounts to the stock steel subframe points (where the stock strap bolts are located). 

Includes high-quality stainless steel mounting hardware, mounts utilize the existing steel subframe rack points (no drilling required), the installation guide is also included. 

Powder-coated satin black for a long-lasting durable finish that looks great on the 300L & Rally! 

Also available in an economy-minded steel version (3.9 lbs)  Please see this product on our site for more details.

Link to product instructions here 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

OVERSTOCK SALE on Rally Link!

For some reason, the CRF 250L and Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginners bike. So we have some options to get your feet firmly back on the ground.

Built in Boise, IDAHO. Ridden and raced everywhere.

We are pleased to offer lowering links by KOUBA LINK:

• 250L L 1.75" Lowering Link: For the standard 2013-2020 CRF 250L, This KOUBA LINK lowers the bike 1-3/4" (44.5mm)

• RALLY 1.5" Lowering Link: This KOUBA LINK lowers the 2017-2020 CRF 250L Rally 1-5" (38mm) in the rear.

 * Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.

However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

The Rally Dual LED headlamp assembly is really cool. It's also $654 to replace......

Protect it from impact damage with the SRC Designs Headlamp guard kit. Laser-cut 14 gauge steel powder coated satin black provides a proper defense against rocks, limbs and other debris you might encounter on your adventures!  

All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools. 

Available in powder coated black or stainless steel (silver)

Fits Honda CRF 250L Rally & 300L Rally 2017-2025

Installation video here.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Installation instructions PDF 

2014-2025 HONDA CB500F, CB500X NX500

Protect your CB500X vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate.  

• Made of 11 gauge ( 1/8" / 3mm) thick 304 aluminum sheet with stainless hardware 
  
• Developed for on and off-road use
  
• The SRC skid plate is compatible with the HONDA and aftermarket accessory center stands.
  
• Compatible & will fit with SRC, Hepco & Becker and SW Motech upper & lower lower crash bars
  
• Please note SRC skid plate is not compatible with the GIVI lower crash bars 
  
• Cutouts allow access to common service points without the need for removal of skid plate

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

*Please note: The arm attachments may not work with aftermarket engine guards, please consult the installation guide or reach out to us with questions.  

*Please note: The slider bars shown on the skid plate are no longer included. SRC recently made a decision to remove the nylon sliders from all of their skid plates after a customer hit a large rock that pushed a slider mounting bolt into the engine case and cracked the case.

  * Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC Crash Bars have cool sacrificial nylon pads that are strategically positioned to be the point of impact if you happen to drop your bike or have a tip over.  If you do happen to scratch one up, you can easily remove it and install a freshie!

These are designed to fit 1" diameter bars. All SRC bars are 1" and they should fit other brands of crash bars that are 1"/25mm diameter. 

 Please Note: These are not solid frame sliders.  Frame sliders are designed to grind away in a fall on the pavement at speed. These are more for tip-overs at low speed to protect the crash bars from scratches etc.  

Price is per replacement pad. (order 1 pad, get 1 pad)

CLOSEOUT SALE! 

Fuel/Jerry Can Mounting Bracket for Royal Enfield Himalayan

(Bracket kit only, no tanks included)

2022-23 model ETA May 10th 2023 

The generous 4-gallon tank on the HIMILAYAN provides a range of about 250 miles. Add up to another 100 miles range with SRC Auxiliary fuel can mounts.  Pre-drilled for easy installation of our 3L fuel cans with mounts, available on our site. 

**NOTE: The base plate is large enough to accommodate the ROTOPAX 2-1/2"  mounting plate bolt pattern but you'll need to drill them yourself.  

The SRC auxiliary fuel can Brackets bolt on using existing mounting points on the HIMALAYAN upper front cargo racks.  Rugged 2 mm thick powder-coated steel brackets have lower and upper support points to provide years of safe and secure service.  Unlike other mounts on the market that only mount at the top and are prone to stress cracking from repeated flexing.

This product includes: Himalayan specific bracket,  (select left or right side when ordering) 

**The full bracket with Fuel/Jerry Can kits are also available on our site.

Product instructions are available here

Available for 2016 to 2023 Royal Enfield Himalayan models

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Full kit install PDF 

Protect your Honda Transalp's vulnerable underside including the exhaust, oil cooler and oil pan, side cases, etc with SRC's heavy-duty crash bars with integrated aluminum skid plate for HONDA's all-new Transalp XR750. 

Fits 2023-2025 Models 

Here is why you need to install protection now!   That is

the 

oil pan 

and exhaust in the red circle in the pic below.

 

 

 

 

 

 

 

Upper Crash Bars installation:  Printed Version 

Lower Crash Bar & Skidplate Installation:  Printed Version 

The steel tube with integrated aluminum skid plate design is lighter (just under 24 lbs) and stronger than conventional two-piece designs. 

• Full crash bars plus 4mm thick integrated aluminum skid plate - sold as a set

• Crash bars made from 1 "diameter steel tube with 2mm wall thickness. Laser cut and formed on a CNC tube bender

• Skid plate and crash bar design allows for oil change and filter replacement without removal and is compatible with the OEM and aftermarket center stands. 

• Crash bars also incorporate a 4mm (3/16") aluminum skid plate to protect the vulnerable cast aluminum oil pan which hangs dangerously below the engine and is pretty much the lowest part of the bike!

• 4 x Main mounting points on each side of the bike for maximum strength

• Beautiful hand-laid TIG welds! 

• Available in black powder-coated and electropolished satin silver stainless steel

• The sacrificial plastic crash bar pads protect the crash bar and reduce impact from falling. They are 

• easily replaced if they are damaged in a tip-over

• Supplied with all stainless steel brackets & mounting hardware

• Easy to assemble, convenient and fast.

*Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged. However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

For some reason, the CRF 300L and Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginners bike. So we have some options to get your feet firmly back on the ground.

Built in Boise, IDAHO. Ridden and raced everywhere.

We are pleased to offer lowering links by KOUBA LINK for the Honda CRF 300L and Rally, which lowers the bike 1-3/4" (44.5mm)

Available in Red or Black colors, make your choice below.

Fits both the standard 2021-2024 CRF 300L and the Rally version.

Also lowers the new 300 LS 1.5" 

Please be aware: All lowering link alter the rear shock linkage leverage ratio, effectively making the rear shock spring softer. And it's already too soft for most riders as it's set up for a 100 lb beginner rider.  If you ride primarily on the street, it probably won't be that big of a deal, but if you ride off-road on loose surfaces, it will have a tendency to make the bike plow through corners instead of carving corners. The front end will push if that makes sense. 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Tail Tidy - Shortened Taillight and license plate bracket HONDA CRF 300L & 300L Rally 2021-2025

NEW Revised version to accommodate US and Global market license plates and license plate lights is shown in the install video above.

Clean up the look of your Honda CRF 300L's back end & license plate holder.

• Made of 3mm stainless steel sheet and held securely in place.
• Easily installed in just a few minutes with common hand tools. 
• Available in Satin Black Powder Coat.

Product instructions are available here * Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Installation PDF 

PLEASE NOTE: This part has been redesigned due to an issue related to the resonant vibration inherent in the KLR.  SRC's new design became available April 12th, 2023. The new design incorporates a fully isolated main mount system using urethane through bushings. 

Protect your KLR's plastics and engine with SRC crash bars.

• Unique design provides full protection of the Upper and Lower engine/body/chassis
• Manufactured out of steel DOM Tubing of 1” diameter and 1.8 mm thickness, and processed in state-of-the-art laser cut machines for cutting, notching and formed by CNC tube bender
• Welded using TIG process and shot blasted to remove all residual stresses, before surface protection process
• Satin Black Electrostatic Powder Coat Finish, provides corrosion resistance to endure all weather conditions
• Kit includes all mounting hardware, bracketry and sacrificial compression molded resin sliders to absorb impact
• Quick, easy and Do it Yourself fitment and Mounting Instructions can be accessed and downloaded from SRC Web site
• Compatible with SRC Skid Plate (when installing skid plate and crash bars, use the longer crash bar bolts at the lower forward attachment points)

Fitment for: Kawasaki KLR 650 & KLR 650S 2022-2025*
* The upper light bar on the adventure model does not have to be removed, but the lower engine guards do. 

Here's a nice video (below) from a customer who installed the crash bars and skid plate at the same time.  When installing the SRC crash bars with SRC skid plate, use the brackets and bolts that come with the skid plate as shown in the video below beginning at around the 3:00 minute mark. 

And here's another customer video showing the install of the SRC skid plate and SRC crash bars. It's an older video, so it shows the earlier version of the crash bars that do not have the urethane isolation bushings, but it does have some helpful information. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

ATTENTION!

The Red ends on the clear and red  lines are on indefinite back order so we opted for polished stainless. 

They look like this. 

Fits: All 2012-2025 CRF250L, Rally 250L , 300L, 300LS & Rally 300L 

(Not available for ABS models)  

PLEASE NOTE: Our front line for the 2012-2024 CRF250L, Rally 250L , 300L & Rally 300L models is 2" shorter than the stock line to reduce clutter and improve the view of the instrument cluster. 

MOTO STUFF premium Steel Braided Brake lines by CORE MOTO are made to our own specifications using only the highest quality materials including Dupont PTFE liners and a tight weave aircraft-grade stainless steel casing covered in Clear, Red or Stealth Black vinyl and an industry exclusive clear translucent HD ACRYLON sheathing to prevent abrasion and provide precise alignment on the bike.

The stainless steel banjo fittings are powder coated bright Red or Blue and are adjustable for precise fitment! Each line also comes with Stainless steel Banjo Bolts and a new set of copper sealing washers.

Upgrading to a stainless line will improve brake lever feel by reducing line expansion, especially on bike with stock rubber lines that are more than 6 months old (around 20-30 hours of use) year old which will begin to flex and balloon when the brakes are applied. Also, the smaller inside diameter of our lines reduces the volume of fluid being compressed so the response is quicker.

Our lines are made using 2.5mm tubing vs the 3mm tubing most common aftermarket braided lines are made of. This improves response. 

The patented adjustable banjo fittings eliminate binding issues and excessive rubbing /abrasion. (easily adjusted using pliers to grip and rotate the line at the crimp joint area) Kit includes 1 line, a set of 4 new crush washers and 2 stainless steel banjo bolts.

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Fits all 2012-2025 HONDA CRF 250L/300L and Rally Models* 

If you've never run a wider high-quality footpeg, you will be pleasantly surprised by the improvement this inexpensive and easy-to-install upgrade will make! Upgrading to a wider platform foot peg (50mm wide and 80mm long) makes a dramatic improvement in comfort as well as greatly improving grip in wet muddy conditions. Our 50mm wide Chrome-Moly pegs are a great value and easy to install.

Our 50mm wide Chrome-Moly pegs are a great value and an easy to install upgrade. Huge upgrade compared to the narrow 38mm stock pegs.

* Please note: The 300L Rally comes equipped with a larger peg than the other models, so not much of an upgrade on that model. 

It only takes about 10 minutes to install with common hand tools. The 50mm width and aggressive tooth profile offer about 50% more contact surface to reduce foot arch strain and improve grip. The wide platform (50mm wide and 80mm long) and increased contact points will improve rider confidence in sketchy situations!

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

The Rally Pro X-Strong is a durable injection-molded Nylon composite handguard that features an anodized aluminum bar for ultimate protection. It includes an indexed steel bar-end insert that mounts solidly and will not allow the guard to rotate in a crash. The included X-Strong mount kit allows the protection to be mounted to the handlebar with plenty of room for cables and brake lines. Optional spoilers are sold separately.

This is a universal part that fits most adventure motorcycles: Please note that some models with adjustable windscreens may need to have the windscreen in the forward-most location, such as the Royal Enfield Himalayan, to avoid contact at full lock. 

These are not compatible on Honda CB500X, NX500 and Honda Africa Twins.

PLEASE NOTE: Some OEM bars will require the removal of weighted bar ends and possibly other minor modifications to install handguards.  

For example- 

Choose from black, white or red colors.

View product instructions here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged. However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Made specific for 2013-2020 Honda CRF 250L & Rally

• Keeps your side stand from sinking into soft ground & hot pavement! 
• Don't find out the hard way why these are so popular! 
• Don't come back to your parked bike to find it on its side after parking on hot pavement or loose soil!

This side stand extension offers a large contact surface (50% larger than stock) to improve the motorcycle’s parking footprint on rough surfaces and soft ground.  

• Easily installed in just a few minutes with common hand tools. 
• Made in high-quality Stainless Steel for long life
• Laser-cut stainless steel with Inox hardware

PRODUCT INSTRUCTIONS AVAILABLE HERE

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

 2020-2024 Full kit in Stainless Steel Silver is on overstock Sale

 Save $100!

NOTE: These are special order products. If the part you want is shown in stock, it will ship right away. However, if the part is out of stock (0 quantity), lead times are generally 4 to 6 weeks. For special order parts, please place your order and we will follow up with the current estimated delivery time. 

ATTENTION!

The body work on the 2025 Tenere 700 is slightly wider than previous models. 

 A new kit for 2025 models is in development and the application listings will be updated as soon as they are available.

SRC Designs Engine/Crash Bar Set for Yamaha Ténéré 700 2019 - 2025* 

2020-2021 full and lower kits are compatible with SRC skid plate.

*2022-2025 models, you can not use the SRC V2 skid plate and lower crash bars. 

PLEASE NOTE! The SRC lower crash bars as well as most others are not compatible with the SRC V2 skid plate. That being said, the SRC V2 skid plate wing extensions do a good job of protecting the lower portions of the engine. 

Also, some international markets received the EURO 5 updates on the 2021 models (larger catalytic converter in the headpipe), North America models did not get this until 2022.  If you are unsure of how to order, shoot us an email for assistance. 

Stout 1" (25mm) steel tube with 1/8" (3mm ) wall thickness CNC Laser cut bracketry and mounts for a precise fit

Available Electropolished Stainless Steel (SILVER) or Satin Black Powder Coat steel 

Includes sacrificial heavy-duty Delrin guards at critical impact zones that are easily replaced if they are damaged in a tip-over

Compatible with the stock skid plate and most aftermarket skid plates

Choose between:

• Full set (Upper and lower crash bars)
• Upper crash bars only (Lower crash bar can be added later to complete full set)
• Lower crash bars only (Upper crash bar can be added to complete full set)

Product weights:

• Yamaha Tenere 700 SRC Crash Bars (Lower): 7.6 LBS 
• Yamaha Tenere 700 SRC Crash Bars (Upper): 14.8 LBS

Installation instructions  Full set and video

Installation Upper Set

Installation instructions lower bar set

Replacement guard/crash bar pads can be found here A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness. These crashbars often contain brown colored blasting media particles found in the ends of the bars.  This is not rust and is perfectly normal.Product installation instructions can be found here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.