For some reason, the CRF 250L and 250L Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginners bike.

NEW Service! 

We are now offering an option to send your seat to us to be lowered. General turnaround time is 3-5 days.  Select the option below. 

Fits 2012-2020 250L & Rally

So we have some options to get your feet firmly on the ground. We are pleased to offer these custom-shaped lowering seats that lower the seat height by 2". These are brand new original HONDA seats that have been hand shaped and re-formed to reduce the seat height by 2" There is still 1-1/2" of foam cushion in the main seating area, so normal ADV riding won't be an issue, but if you are a hard-charging off-roader frequently getting airborne, it might be a bit firm on some landings! :-) 

These were developed after my wife was about to give up on her Rally as it was too tall for her. She is relatively new to offroad riding and really felt unsafe and uncomfortable on the Rally, especially when riding on sidehills and slippery surfaces where she was not able to touch the ground when needed. We had already installed a lowering link and that helped, but she wanted it lower to feel comfortable. So we gave one of these a try and she now loves her Rally!  Easily installed in just a couple of minutes with common hand tools. 

Now available in your choice of RED or BLACK- Please make a selection

We occasionally get further inquiries regarding lowering options and this is our general reply: 

The cons of running a link are due to the geometry change in the suspension. In a nutshell, the bike becomes "choppered out" slightly. So the bike likes to go straight (improves straight-line stability), but when cornering on loose surfaces such as gravel roads or lose dirt, the bikes front end will have a bit more of a tendency to plow or push through corners. This is not noticeable on pavement and a beginner off road rider probably won't push the limits of traction enough to have it be an issue, but if you are an experienced off-road rider, you will most likely notice it.  

* These are brand new original HONDA seats that have been hand shaped and re-formed to reduce the seat height by 2" 

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality. 

SAVE BIG BUCKS on the best kits while supplies last!  

Crash Bars / Engine Guards 2017-2023 Royal Enfield Himalayan and SCRAM 411

• Available electropolished 304 stainless steel silver or satin black powder coat steel  
• Stout 1" (25mm) tube with 1/8" (3mm ) wall thickness
• CNC Laser cut bracketry and mounts for a precise fit
• Sacrificial heavy-duty delrin guards at critical impact zones that are easily replaced if they are damaged in a tip-over
• Design of guards allows for easy access to the oil filter

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

Product instructions located here

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.

However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

Your HIMALAYAN comes with a beautiful classic 7" round H4 halogen headlight that actually puts out a decent swath of light!  Protect it from road debris impact damage with the SRC Designs Headlamp guard kit.

Available in your choice of satin black powder coat laser cut 14 gauge steel or natural brushed stainless steel finish.   

The SRC headlight guard provides a proper defense against rocks, limbs, and other debris you might encounter on your adventures!  

All mounting hardware is included and the guard is easily installed in about 10 minutes with common hand tools. The trick pin mount system allows for quick removal for cleaning with no tools! 

Easily installed in just a few minutes with a Phillips screwdriver. 

PLEASE NOTE: If you are running the windscreen in the upright position, you can install the headlight guard in that position, but it will be tilted forward a bit at the top. To keep it square to the headlight, you will have to make a slight modification to the windscreen to expose the lower mounting hole.  (use a round file to remove enough material to allow the rearmost headlight guard mounting bolts to be installed.)

Product instructions located here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

 For some reason, the CRF 250L and Rally's have really tall seat heights (over 35" and taller than the AFRICA TWIN!?! ), especially for a small displacement beginners bike. So we have some options to get your feet firmly back on the ground.

Built in Boise, IDAHO. Ridden and raced everywhere.

We are pleased to offer lowering links by KOUBA LINK:

• 250L L 1.75" Lowering Link: For the standard 2013-2020 CRF 250L, This KOUBA LINK lowers the bike 1-3/4" (44.5mm)

• RALLY 1.5" Lowering Link: This KOUBA LINK lowers the 2017-2020 CRF 250L Rally 1-5" (38mm) in the rear.

 * Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.

However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

Fuel/Jerry Can Mounting Bracket for Royal Enfield Himalayan

(Bracket kit only, no tanks included)

The generous 4-gallon tank on the HIMILAYAN provides a range of about 250 miles. Add up to another 100 miles range with SRC Auxiliary fuel can mounts.  Pre-drilled for easy installation of our 3L fuel cans with mounts, available on our site. 

**NOTE: The base plate is large enough to accommodate the ROTOPAX 2-1/2"  mounting plate bolt pattern but you'll need to drill them yourself.  

The SRC auxiliary fuel can Brackets bolt on using existing mounting points on the HIMALAYAN upper front cargo racks.  Rugged 2 mm thick powder-coated steel brackets have lower and upper support points to provide years of safe and secure service.  Unlike other mounts on the market that only mount at the top and are prone to stress cracking from repeated flexing.

This product includes: Himalayan specific bracket,  (select left or right side when ordering) 

**The full bracket with Fuel/Jerry Can kits are also available on our site.

Product instructions are available here

Available for 2016 to 2023 Royal Enfield Himalayan models

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

ENGINE GUARD / Skid Plate FOR BMW G 310GS & BMW 310R 2017-2025

• Made of 1/8" ( 3mm) thick  Satin Black Powder Coated or Clear  
• Anodized Aluminum 
• Developed for on and off-road use
• Fits 2017-2025 BMW G310 GS & BMW 310R 
• Easily installed with common hand tools
• Stainless Steel mounting hardware and Installation guide included 
• Cutouts allow access to common service points without the need for removal of skid plate

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

Link to product instructions here

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

 2020-2024 Full kit in Stainless Steel Silver is on overstock Sale

 Save $100!

ATTENTION!

The upper body work on the 2025 Tenere 700 is slightly wider than previous models.  The lower kits below do fit the 2025.-2026  

 A new full kit   2025 and 2026 models is now available here on our website. 

SRC Designs Engine/Crash Bar Set for Yamaha Ténéré 700 2019 - 2025* 

2020-2021 full and lower kits are compatible with SRC skid plate.

*2022-2025 models, you can not use the SRC V2 skid plate and lower crash bars. 

PLEASE NOTE! The SRC lower crash bars as well as most others are not compatible with the SRC V2 skid plate. That being said, the SRC V2 skid plate wing extensions do a good job of protecting the lower portions of the engine. 

Also, some international markets received the EURO 5 updates on the 2021 models (larger catalytic converter in the headpipe), North America models did not get this until 2022.  If you are unsure of how to order, shoot us an email for assistance. 

Stout 1" (25mm) steel tube with 1/8" (3mm ) wall thickness CNC Laser cut bracketry and mounts for a precise fit

Available Electropolished Stainless Steel (SILVER) or Satin Black Powder Coat steel 

Includes sacrificial heavy-duty Delrin guards at critical impact zones that are easily replaced if they are damaged in a tip-over

Compatible with the stock skid plate and most aftermarket skid plates

Choose between:

• Full set (Upper and lower crash bars)
• Upper crash bars only (Lower crash bar can be added later to complete full set)
• Lower crash bars only (Upper crash bar can be added to complete full set)

Product weights:

• Yamaha Tenere 700 SRC Crash Bars (Lower): 7.6 LBS 
• Yamaha Tenere 700 SRC Crash Bars (Upper): 14.8 LBS

Installation instructions  Full set and video

Installation Upper Set

Installation instructions lower bar set

Replacement guard/crash bar pads can be found here A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness. These crashbars often contain brown colored blasting media particles found in the ends of the bars.  This is not rust and is perfectly normal.Product installation instructions can be found here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

 Robust enough to protect the vulnerable and expensive radiator against flying stones and other debris.
- This protector made of stainless steel sheet 304 grade 1.5 mm thickness
- Can be easily mounted in a few minutes with common hand tools on the radiator for BMW G 310 GS / 2017- 2025

Available in natural brushed silver or satin black powder-coat finishes 

Link to product instructions here

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Available in Brushed Stainless Steel finish or Satin Black Powder coat steel 
- Pin Mounting allows for quick tool-less removal for cleaning of the headlight lens 
- Developed for on or off-road use
- Fits BMW G 310 GS 2017-2025

Includes all necessary mounting hardware and is easily installed with common hand tools. 

Link to product instructions here

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

For 2017-2021, the top rack is just a top plate that bolts to the existing rack frame. The black version has sold out. 

The newly designed rack for 2022-2023 Himalayan and the 2022-2025 SCRAM 411 and features an all-new beefy 1" diameter frame structure that completely eliminates the failure-prone stock rack frame.  It also incorporates small side wings (approximately 6" tall by 10" long) to help keep soft luggage out of the tire/wheel area.  The new 2022-2023 rack kit is not compatible with the Royal Enfield Pannier Racks. 

Top rack is made of a strong 3mm aluminum alloy plate for an optimal balance of strength to weight.

Rack plate dimensions:

Approximately 10" long, 11" wide at the front, tapering to 8" at the rear.  

Available in satin black powder coat or clear anodized natural silver to prevent oxidation. Designed for use with the stock rear tail rack and is also compatible with the Royal Enfield accessory side Pannier rack.  

NOTE: The accessory quick attachment kit for use with Kappa, GIVI, MONOKEY Hard Cases (and shown in the images) is No longer available

Product instructions are available here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Overstock reduction Sale! 

Fits HONDA CB500X 2013-2023

Robust enough to protect the vulnerable and expensive radiator against flying stones and other debris.
- This protector made of stainless steel sheet 304 grade 1.5 mm thickness
- Can be easily mounted in a few minutes with common hand tools 

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! (black has sold out) 

Protect the vulnerable header downpipe from road debris, rocks, and tip-over impacts with the SRC Header Pipe guard.

2-year ranges are available:

• Fits 2016-2021 ROYAL ENFIELD HIMALAYAN/SCRAM 411 (Pre Catalytic Converter models)
• Fits 2022-2023 ROYAL ENFIELD HIMALAYAN/SCRAM 411 (Models with Catalytic Converter

Made of 2mm stainless steel sheet and held securely in place with low profile stainless steel band clamps.  Easily installed in just a few minutes with common hand tools and provides years of protection.

Available in both Stainless Steel and Satin Black Powder Coat options.

Product instructions are available here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Keeps your side stand from sinking into soft ground & hot pavement! 

Don't find out the hard way why these are so popular! 

Don't come back to your parked bike to find it on its side after parking on hot pavement or loose soil!

SIDE STAND BASE ENLARGER FOR BMW G 310 GS  2017-2023

The SRC large side stand base extension installs easily and improves your parking experience when off pavement with your bike.
- Made of laser cut stainless steel sheet 304 grade 3 mm thickness
- Stainless bolts and lock nuts 
- Easy installation
- Keeps your side stand from sinking into the soft ground

The SRC large side stand base extension (doubles the surface area) installs easily and improves your parking experience when off pavement with your bike.

Link to product instructions here

* Note: SRC MOTO is located in Oregon which is one US state that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC Designs Full Rack System for the 2021-2025 CRF HONDA 300L/Rally 300L and 300LS The SRC Rack is designed to allow access to the toolbox under the left side panel as can be seen in the images below.

Full rack with Fuel can is also available on our site. 

Top rack surface dimensions are roughly 14” long and 9’ wide at the front, tapering to 8” at the rear. 

Side racks add other 12” X 6” top surface making the full rack top surface roughly 14” X 20” 

Side rack dims are approximately 12” X 8” 

This is the Adventure Rack System you want! 

Innovative modular design made of high-strength lightweight aluminum alloy. (Entire rack only weighs 4.8 lbs! )

The SRC Designs Full Rack System includes left and right pannier racks, center tail rack, mounting hardware, and instructions (easily installed in about 30 minutes with common hand tools)

The Full Rack System features: 

• High-quality stainless steel mounting hardware, mounts using the existing steel subframe rack points (no drilling required)
• Pre-Drilled for MOTO STUFF Fuel can quick-release mount. (Not compatible with ROTOPAX) Although a ROTOPAX can be installed on the exterior sides., just not on the interior as shown as the ROTPAX is too tall. 
• Side racks and top rack feature strategically positioned strap slots for quick and secure attachment of most brands of soft luggage.
  
• The SRC Rack is designed to allow access to the tool box under the left side panel as can be seen in the images below.
• Center Tail Rack is nicely sized and shaped to fit the rear of the bike and provides a nice solid foundation for luggage, camping gear, etc. The aluminum rack (weighs just over a pound, and about 3 pounds with the side racks installed) mounts to the stock steel subframe points (where the stock seat bolts are located).  

Powder-coated satin black for a long-lasting durable finish that looks great on the 300L!

Please Note: The CRF 300L/Rally specifications indicate a max subframe load of 35 lbs. We have been loading our racks with nearly 60 pounds of gear for the past 2 years and have put about 8,000 miles on our 2 Honda's over all types of terrain and we have not had any issues with the racks or subframe, but the more extreme your usage, it is something to be aware of and take into consideration. 

Product Instructions available here

Product installation video available here

Another video we did that's a bit more detailed and shows how the gas can is easily removed. 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

SRC DESIGNS GPS bracket bar 2016-2023 HONDA CB500X

Available in Satin finish stainless steel silver or satin black powder coat.

The SRC DESIGNS GPS bracket bar gives you a solid attachment point on your bike. Gone are the days of trying to read shaky GPS screens. Made of stainless steel and anodized aluminum, this handlebar mounting adapter is built to go the distance.

The GPS mount adapter provides a sturdy 22mm (7/8" inch) diameter mounting bar that is intended for mounting most GPS mounts. It can also be used for roadbook holders or any other device that uses a  common 7/8" clamp.

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Crash Bar Set HONDA CB500X

Not compatible with Rally Raid skid plate

Choose between:

• HONDA CB500X 2019 - 2023 (Black or Silver) 
  
•   2024-2025  NX 500 Kit available here 

Available electropolished 304 stainless steel silver or satin black powder coat steel  

• Stout 1" (25mm) tube with 1/8" (3mm ) wall thickness
  
• CNC Laser cut bracketry and mounts for a precise fit
  
•  Sacrificial heavy-duty plastic guards at critical impact zones that are easily replaced if they are damaged in a tip-over
  

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

Installation instructions PDF

*Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Protective Aluminum Skid Plate SUZUKI V-STROM 800DE 2023-2025

Protect your V-STROM DE's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate/ lower engine sump guard/skid plate. 

Is compatible with the stock center stand    

• Fits SUZUKI V-STROM 800DE 2023-2025*
• Available in clear anodized brushed aluminum or satin black powder coat aluminum
• Made of 11 gauge ( 1/8" / 3mm) thick  304 aluminum sheet with stainless hardware. 
• Developed for on and off-road use
• Cutouts allow access to common service points without the need for removal of skid plate

* Can be installed on the base V-Strom 800 model by first installing the SUZUKI accessory lower frame

PRINTED PRODUCT INSTRUCTIONS AVAILABLE HERE

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Overstock price reduction on Silver 

SRC Designs Head Light Guard for Yamaha Ténéré 700

Fits Yamaha Ténéré 700 years 2019 - 2024.

2025-2026 model is also available on our website.  headlight design 

Available in Brushed Stainless Steel finish or Satin Black Powder coat steel 

• Pin Mounting allows for quick tool-less removal for cleaning of the headlight lens 
• Developed for on or off-road use

Includes all necessary mounting hardware and is easily installed with common hand tools. 

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Radiator Guard HONDA NX500

Fits HONDA NX500 2024-2026

Robust enough to protect the vulnerable and expensive radiator against flying stones and other debris.
- This protector made of stainless steel sheet 304 grade 1.5 mm thickness
- Can be easily mounted in a few minutes with common hand tools 

Installation instructions 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

The single biggest complaint from CRF 300L and Rally owners is that the suspension is sprung way too light and the damping is inadequate. The bike seems to be set up for a 100-pound beginner rider- Here's how to fix that.  A heavier spring or adjusting the pre-load will not resolve the issue. 

Front Fork kit fits 2021-2025 CRF 300L & Rally/Rally ABS   
The Fork kit comes with 3 springs, one light spring for 300L riders up to 175 lbs (7.5N/mm), one stiffer for 175+ 300L and Rally riders (8.5N/mm), the last hard spring for Rally riders (9.5N/mm). The kit also includes billet fork caps with integrated air bleeders to allow easy air bleed and keep your suspension nice and plush!

 PLEASE NOTE!  The CRF 300L and Rally models only have 1 fork spring and it is housed inside the right fork leg. Also, there is a single aluminum spring spacer included in the Ohlins fork spring kit, it goes on top of the right spring.  

The CRF 300L Rally Recommended Fork oil volume 
(Use a good quality 30 wt. fluid for best results) Ohlins fluid is available here on our site. 

PS- If you are installing the kit yourself, PLEASE NOTE! 

OS-6 ADVENTURE PACK is specifically designed for riding in the most demanding of environments. Use as a single stand-alone pack or as a multi-pack storage system with the addition of other packs in the OS range.

The 100% waterproof roll-top closure (removable white liner) guarantees pack contents remain protected from the elements.

Constructed from the highest quality materials including ultra-abrasion resistant Hypalon™+ 1000D Cordura® and aircraft grade alloy hooks.

A semi-rigid SureGrip rubberized base with integrated hook loops and straps enables the pack to be mounted directly to most popular racks and pannier frames. Alternatively, it can be mounted in various ways using the alloy hooks with other Kriega loop systems, making the OS-6 a very versatile pack.

FEATURES

• 100% waterproof liner
• Roll-top closure
• HYPALON™+ 1000D Cordura®
• Aircraft-grade alloy buckles
• Heavy-duty Acetal cam buckles
• Hi-Vis details
• Shoulder strap loops

MOUNTING OPTIONS

The four Integrated loops on the base of each pack are designed to:

• Mount directly to most rear racks  
  
• Mount to an OS-BASE as a side pannier or tail pack
  
• Mount as a tail pack with Kriega OS RACK LOOPS
  
• Hook on to an OS-32 pannier (front, rear or top)
• Mount directly to most front crash bars     
• Mount as a tank bag with Kriega TANK or SUBFRAME LOOPS

 An optional OS-SHOULDER STRAP can be hooked on to convert to a shoulder bag. (sold separately)

TECH SPEC

DIMENSIONS

• 320(h) x 200(w) x 90(d) mm
• 12.5(h) x 7.9(w) x 3.5(d) ins.

CAPACITY: 6 Litres - 366 cu in

WEIGHT: 550g - 19.4 oz

 ARCHIVED DUE to slow sales 5-5-26

SRC Designs Cargo Tail Rack for Yamaha Ténéré 700 2020 - 2025

The top plate is made of strong 3mm aluminum alloy plate for an optimal balance of strength to weight. Lots of openings for strapping and bungee cords.  This rack also includes stainless steel support brackets and is rated for up to 22 lbs  (10 Kg) of gear. 

Comparing this V2 HD tube frame rack with our V1 center rack, the center top rack of the V1 is good for small luggage set up and especially Kriega luggage, however, if you need access to the battery or electrics whilst on a ride you need to remove the rack which can be a little annoying and secondly the V1 rack fits over the passenger seat so no place for a passenger to sit. The full version of the V1  top rack with side racks is good for riders that have soft luggage as the side racks are slightly raised off the side with rubber stands offs so they stop potential damage caused by luggage rubbing on the plastics.

This new rear rack (V2) with grab rails is great as it allows access to the air filter & electrics etc. without need to remove the seat whilst out on a ride. The real benefit of V2 is using the grab rails to pick up the bike or lift the bike out of ruts & muddy holes etc...as T7 has nothing to hold onto at rear of bike. This V2 option allows for much larger luggage to be carried as racks sits further out off the back of bike. On a side note, the V2 version can also act as rear crash bars as they stick slightly out from the side of bike. We've tested all options and this also comes from reliable customer feedback.

Pre-drilled for our 3L fuel can mount

Available in Satin Black powder coat

Fitment:

• Yamaha Ténéré 700 years 2020 - 2025
• • Black powder-coated 3.25mm aluminium top plate
    
  • 25mm (1") Chro-moly steel tube frame for increased load capacity and weight distribution.  Plus acts as much much-needed grab handle!
  • Fits to 4 x existing mounting points on rear of bike
  • Supplied with 4 x stainless steel standoffs to replace existing OEM units 
  • Includes all stainless steel mounting bolts & counter-sunk washers
  • Flat section of the rack sits  approximately 10mm above the passenger seat (standard OEM seat)
  • Slotted all around to cater for plenty of tie-down points
  • Pre-drilled to fit SRC 3 liter plastic fuel tank
  • Easy to drill holes to fit the Roto-Pax fuel/water containers in a position to suit you
  • Quick & easy fitment
    
  
  

Installation instructions and video

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE! 

Black has sold out. 

SRC Designs Frame Guard (Left side) for Yamaha Ténéré 700

Fits Yamaha Ténéré 700 years 2020 - 2025

Protect the header downpipe from rocks, road debris, and tip over impacts with this slick stainless steel guard laser cut from stainless steel. 

• Crafted out of 2 mm thick aircraft fuselage grade stainless steel
• Laser-cut, CNC bent on state-of-the-art machines
  
• Easy 5-minute install using the stock fasteners and common hand tools
• Available in natural silver stainless finish or black powder-coated

Product installation information can be found here

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

CLOSEOUT SALE!

Fits 2019-2023  HONDA ADV150

Trick lightweight aluminum tail rack in silver brushed aluminum or satin black powder coat with top-quality stainless hardware for your ADV150!  

This rack includes a tubular structural support brace that greatly improves the load capacity compared to other racks that simply attach directly to the subframe.  You can safely carry up to 35 lbs  (16 Kg's) with this rack system. 

Rack is approximately 11"wide at the front and tapers to 8" in the rear and is 11" long. 

No drilling or modifications required, easily mounts in under an hour with common hand tools. 

Installation video 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.

However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

ADV 150

Crash Bar Set 2019-2023 HONDA ADV150 

• Stout 1" (25mm) tube with 1/8" (3mm ) wall thickness
  
• CNC Laser cut bracketry and mounts for a precise fit
  
•  Sacrificial heavy-duty plastic guards at critical impact zones that are easily replaced if they are damaged in a tip-over

Installation instructions 

*Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

ADV 150

CLOSEOUT SALE, SAVE OVER $200! 

Black is sold out

SRC Designs Protective Aluminum Skid Plate/Lower Engine Sump Guard for Yamaha Ténéré 700

Fits Yamaha Ténéré 700 years 2019 - 2021*

Does not fit 2022-2023 or models equipped with E5 catalytic converter

Protect your  Tenere's vulnerable underside including the exhaust, oil cooler, side cases, etc with SRC's heavy-duty skid plate.  

• Made of heavy gauge 4mm thick aerospace fuselage aluminum sheet with stainless brackets and hardware. 
• Developed for on and off-road use
• Cutouts allow access to common service points without the need for removal of skid plate

Available in brushed stainless steel or satin black powder-coat

A common question is “Can the skid plate and crash bars be installed together?”  Yes, both parts include spacers that are used in the main mounting locations when the part is installed by itself. When adding the second part, the spacer is removed to allow room for the 2nd parts mounting bracket thickness.

Installation instructions and video 

* Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.
However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

Installation PDF 

SRC Designs Cargo Tail Rack for Yamaha Ténéré 700 2021-2025 Version 1 (V1) 

Made of strong 3mm aluminum alloy plate for an optimal balance of strength to weight. Lots of openings for strapping and bungee cords.  This rack also includes stainless steel support brackets and is rated for up to 22 lbs  (10 Kg) of gear. 

• Black powder coated aluminium
• Laser cut 3.25mm aluminium plate 
• Light but super strong - only 1.3kg 
• Fits to 4 x existing mounting points on rear of bike
• Supplied with 4 x stainless steel standoffs to replace existing OEM units 
• Includes all stainless steel mounting bolts & counter-sunk washers
• Flat section of the rack sits  approximately 10mm above passenger seat (standard OEM seat)
• Slotted all round to cater for plenty tie down points
• Pre drilled to fit SRC 3 litre plastic fuel tank
• Easy to drill holes to fit the Roto-Pax fuel/water containers in a position to suit you
• Quick & easy fitment
• Please note this rack will not fit with the rally seat 
• Fuel tanks & fuel tank mounting brackets as seen in some of the photos are not included in price (sold as separate parts) 

The top rack is good for small luggage set up and especially Kriega luggage, however if you need access to the battery or electrics whilst on a ride you need to remove the rack which can be a little annoying and secondly the rack fits over the passenger seat so no place for a passenger to sit. The top rack with side racks is good for riders that have soft luggage and side racks are slightly raised off the side with rubber stands-offs so they stop potential damage caused by luggage rubbing on the plastics. The new rear rack V2 with grab rails  (available here) is great as it allows access to air filter & electrics etc. without the need to remove the seat whilst out on a ride. The real benefit of V2 is using the grab rails to pick up the bike or lift the bike out of ruts & muddy holes etc...as T7 has nothing to hold onto at the rear of the bike. This V2 option allows for much larger luggage to be carried as racks sits further out off the back of the bike. On a side note, the V2 version can also act as rear crash bars as they stick slightly out from the side of bike. We've tested all options and this also comes from reliable customer feedback.

Fitment:

• Yamaha Ténéré 700 years 2020 - 2023*

• *Not compatible with optional rally seat

Installation instructions and video*

Note: SRC MOTO is located in Oregon which is one of the few US states without a general sales tax, so none is charged.However, when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

OVERSTOCK SALE!  

Center Stand Guard for Ducati Multistrada

Fits: 2015-2020 Ducati Multistrada 950 / 1200 / 1260

Protect the underside of your Multistrada from damage with the SRC Center Stand Guard. Easily installed in minutes with common hand tools.  

Constructed of strong yet lightweight Aluminum and processed in state-of-the-art laser cut and CNC bending machines.

Customer input from Troy S. "This skid plate extender is perfect as there was a significant gap in coverage, leaving the rear header pipe completely exposed. This Center Stand Plate covers it giving more assurance I will not destroy the pipe as I surmount large logs, rocks, and berms."

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.

TOP CASE RACK FOR BMW G310 GS 2017-2025

SRC DESIGN Cargo Racks* are made of lightweight strong 3mm aluminum alloy plate for an optimal balance of strength to weight. CAD designed and manufactured for a sleek and precise fit to match the rear profile of your bike and provide generous surface footprint with an abundance of attachment points for hooks, straps, and packs. 

Available in Satin Black powder coat or Clear anodized natural silver to prevent oxidation.

Please note: Accessory quick attachment kit for use with Kappa, GIVI, MONOKEY Hard Case shown in the images is not included with this product but is available as well.  If this is needed, please see this add-on product on our site: "Quick-release mounts" 

Link to product instructions here

* Note: SRC MOTO is located in Oregon which is one of the few US states that does not have any general sales tax, so none is charged.
However, please be aware when shipping outside the USA, import tax, duties, and other local taxes may still be charged by the destination government or municipality.